Raven Sidekick Pro ISO Installation & Operation Manual Download Page 26

Page: 26 / 82

HAPTER

Sidekick Pro™ ISO Installation & Operation Manual

FIGURE 10. Sidekick Pro™ ISO Pump Mounting Bracket Bolt Pattern

SIDEKICK PRO™ ISO INJECTION SYSTEM PLUMBING

PLUMB THE SIDEKICK PRO™ ISO PUMP

PUMP INLET

Use 3/4” chemically resistant hose between the chemical tank and injection pump inlet. Do not use hose or tubing

that may collapse when a vacuum is applied during pump operation.

The product line should be as straight as possible. Avoid low spots in plumbing to ease pump priming and avoid

chemical waist.

STRAINER

A strainer with a #20 mesh screen must be installed on the inlet side of the injection pump.

PUMP OUTLET

Connect the pump outlet to the injection check valve at the point of injection. Use the following hose sizes

depending upon the capacity of the injection pump used with the system.

Pump Capacity

Hose Size

1-40 oz./min.

3/8”

Summary of Contents for Sidekick Pro ISO


















































































Search results

Summary of Contents for Sidekick Pro ISO

Reviews:

Brands by name

Popular brands

Raven Sidekick Pro ISO, Installation & Operation Manual

Search results

Summary of Contents for Sidekick Pro ISO

Reviews:

Brands by name

Popular brands