background image

 

 

 

 

  

PAGE 11/24 | Calibration manual | 016-8000-015EN | Rev. A 

CALIBRATE ISO RAVEN STEERING CONTROLLER | CR7 AUTOSTEERING | RAVEN EUROPE GENERIC 

21 

When Satellite GS (accuracy 3-5cm) is 
available (subscription needed), select 
Satellite GS. The receiver needs to have an 
unlock. When Satellite GS is selected, the 
subscription status is shown below.  

 

22 

When RTK (accuracy 0-2cm) is available 
(Slingshot RTK modem is needed next to the 
Raven 600S), select RTK. After that, it is 
possible to setup the RTK Format and the 
Correction Baudrate. When using Slingshot 
RTK, leave this on Auto and on 115200. 

 

23 

In this case SBAS is used. Select SBAS and 
leave Differential Satellite on Auto. The 
selected SBAS satellite (#) is shown (in this 
case, 0120). 

Press next step.  

 

24 

The GPS Status Information is shown. The 
satellite needs to be green and the Status 
needs to be Converged.  

This can take a few minutes, depending on 
the view of the antenna (when there are 
buildings around it can take longer as in the 
middle of a field). 
When converged, press next step. 

 

Summary of Contents for CR7

























Reviews: