manualshive.com logo in svg

Raven AutoBoom XRT, Calibration & Operation Manual

Share
Download
Raven AutoBoom XRT Calibration & Operation Manual Download Page 44

C

HAPTER

 5

40

AutoBoom XRT Calibration & Operation Manual

FIGURE 30.  Auto Calibration - Results

7. Repeat step 5 and step 6 four more times. Each test will result in a higher boom velocity.
8. Raise the boom to 5° above horizontal. Touch the Next button to continue, the boom will lower slowly.

FIGURE 31.  Auto Calibration - Right Boom Angle

9. An average speed will be displayed. After 5 seconds the boom will return to 5° above horizontal. Touch the 

Next arrow to bypass the 5 second pause.

10. Repeat step 8 and step 9 four more times. Each test will result in a higher boom velocity.
11. Repeat step 5 through step 10 for the left boom.
12. At the completion of calibration, a calibration summary page will be displayed. Press the check button to 

accept the new values or the X button to exit the calibration process without saving the new values.

Summary of Contents for AutoBoom XRT









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands