Raven 40710D-600 User Manual Download Page 9 | Manualshive

Page: 9 / 23

background image

CHAPTER 3

POWERING UP THE SNI SHELF

Powering Up the SNI Shelf

Reinstall the 41632 card, if previously removed, before performing the
following steps. Also, make sure the source power supply is still turned off.

1. With the front panel removed, verify the toggle switch is in the “off”

position (to the right).

2. Turn on the external power source.
3. Flip the toggle switch to the “on” position (to the left).
4. The green light on the 41620 card (Power Supply) should be

illuminated. If not, please refer to Chapter 5, Troubleshooting and
Alignment.

5. Reattach the front panel.

7

«
...
7
8
9
10
11
...
»

Summary of Contents for 40710D-600
























Reviews:

No comments

Related manuals for 40710D-600

Brand: MacDon Pages: 89

Brand: Yates Pages: 2

Brand: Ecco Pages: 3

Brand: MacDon Pages: 84

Brand: MacDon Pages: 89

Brand: Patton electronics Pages: 18

Brand: Keithley Pages: 42

Brand: ACE INSTRUMENTS Pages: 15

Brand: Wave Fitness Pages: 15

Brand: Major Pages: 52

Brand: Maico Pages: 55

Brand: Maico Pages: 38

Brand: Maico Pages: 2

Brand: MAHA Maschinenbau Haldenwang Pages: 13

AirForm Night Splint

Brand: Össur Pages: 16

Brand: Össur Pages: 17

STOMAMED COL-160

Brand: Orliman Pages: 12

Brand: K-SPORT Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands