background image

17

Safety precautions

Power supply

Do not use a modi

fi

 ed cord, 

joint cord, extension cord or 

unspeci

fi

 ed cord to prevent 

overheating and 

fi

 re.

  

To prevent overheating, 

fi

 re or electric shock:

• Do not share the same power outlet with other 

equipment.

• Do not operate with wet hands. 

• Do not over bend the power supply cord.

• Do not operate or stop the unit by inserting or 

pulling out the power plug.

If the supply cord is damaged, it must be 

replaced by the manufacturer, service agent 

or similarly quali

fi

 ed persons in order to avoid 

a hazard.
It is strongly recommended to be installed 

with Earth Leakage Circuit Breaker (ELCB) 

or Residual Current Device (RCD) to prevent 

electric shock or 

fi

 re.

To prevent overheating, 

fi

 re or electric shock:

• Insert the power plug properly.

• Dust on the power plug should be periodically 

wiped with a dry cloth.

Stop using the product if any abnormality/

failure occurs and disconnect the power plug or 

turn off the power switch and breaker.

(Risk of smoke/

fi

 re/electric shock) 

Examples of abnormality/failure

• The ELCB trips frequently.

• Burning smell is observed.

• Abnormal noise or vibration of the unit is 

observed.

• Water leaks from the indoor unit.

• Power cord or plug becomes abnormally hot.

• Fan speed cannot be controlled.

• The unit stops running immediately even if it 

is switched on for operation.

• The fan does not stop even if the operation 

is stopped.

Contact your local dealer immediately for 

maintenance/repair.
Replacement or installation of power plugs 

shall be performed by authorised/quali

fi

 ed 

personnel only. The wires in this mains lead are 

coloured in accordance with the following code:

Terminals

Red

wires

live

neutral

earth

colours (GB Standard)

blue

green-yellow

brown

Black

Green/Yellow

Wiring colour may vary depending on a country

wiring code’s standard.

This equipment must be earthed to prevent 

electrical shock or 

fi

 re.

Prevent electric shock by switching off the 

power supply and unplug:

- Before cleaning or servicing,

- When extended non-use, or

- During abnormally strong lightning activity.

CAUTION

Indoor unit and outdoor unit

Do not wash the indoor unit with water, 

benzine, thinner or scouring powder to avoid 

damage or corrosion at the unit.
Do not use for preservation of precise 

equipment, food, animals, plants, artwork 

or other objects. This may cause quality 

deterioration, etc.
Do not use any combustible equipment in front 

of the air

fl

 ow outlet to avoid 

fi

 re propagation.

Do not expose plants or pet directly to air

fl

 ow to 

avoid injury, etc.

Do not touch the sharp aluminium 

fi

 n, 

sharp parts may cause injury.

Do not switch ON the indoor unit when waxing 

the 

fl

 oor. After waxing, aerate the room properly 

before operating the unit.
Do not install the unit in oily and smoky areas 

to prevent damage to the unit.
Do not dismantle the unit for cleaning purpose 

to avoid injury.
Do not step onto an unstable bench when 

cleaning the unit to avoid injury.
Do not place a vase or water container on the 

unit. Water may enter the unit and degrade the 

insulation. This may cause an electric shock.
Do not open window or door for long time 

during operation, it may lead to inef

fi

 cient 

power usage and uncomfortable temperature 

changes.
Prevent water leakage by ensuring drainage 

pipe is:

- Connected properly,

- Kept clear of gutters and containers, or

- Not immersed in water
After a long period of use or use with any 

combustible equipment, aerate the room 

regularly.
After a long period of use, make sure the 

installation rack does not deteriorate to prevent 

the unit from falling down.

Remote control

Do not use rechargeable (Ni-Cd) batteries. It 

may damage the remote control.

To prevent malfunction or damage of the 

remote control:

• Remove the batteries if the unit is not going to 

be used for a long period of time.

• New batteries of the same type must be 

inserted following the polarity stated.

Power supply

Do not disconnect the plug by pulling the cord 

to prevent electric shock.

English

Summary of Contents for RS-YS18UK





























Reviews: