Rasilient PixelStor 5000 User Manual Download Page 43

Page: 43 / 161

Hardware Installation

PixelStor 5000 User Manual
Rev. 1, May 2013

3-6

Figure 3-6 Release the Controller Module

3.3.2

Controller Fan Board

The PixelStor 5000 is designed with two 600 watt power supply modules with fan to provide

redundant power for the entire enclosure. One power supply provides enough power to boot up

and run a fully loaded system. The second power supply/fan assembly serves as a backup in

the event of a system failure and provides cooling.

Each power supply module contains two non-removable external fans to cool the power supply

module. The power supply module shuts itself down if the specified limit is exceeded for

temperature or output current.

Features:



On/Off DC power switch



Two Non removable variable speed fans



AC plug receptacle



Power supply status LEDs (AC present, power on and AC fault)

Reminder

Before you remove a power supply module, disconnect the power supply power cord from

AC power and then from the power supply.

To install the Power Supply/Fan assembly

Carefully insert the Power Supply/Fan assembly into the bay with the handle fully opened until it

completely enters the bay.

Summary of Contents for PixelStor 5000


































































































































































Search results

Summary of Contents for PixelStor 5000

Reviews:

Related manuals for PixelStor 5000

Brands by name

Popular brands

Rasilient PixelStor 5000, User Manual

Search results

Summary of Contents for PixelStor 5000

Reviews:

Related manuals for PixelStor 5000

Brands by name

Popular brands