Visit us at
www.rapala.ca
6
Operator's Manual
RAPALA
®
Power Ice Auger
(SERVICE, continued from page 5)
When servicing or repairing the engine, do not tip the engine
over or up unless specifically instructed to do so in this manual.
Service and repair procedures can be done with the engine
in an upright position. Some procedures will be easier if the
engine is lifted on a raised platform or working surface.
• To reduce fire hazard, keep engine free of debris build-up.
Clean up oil or fuel spillage. Allow engine to cool before
storing.
• Stop and inspect the equipment if you strike an object.
Repair, if necessary, before restarting.
• Clean and replace safety and instruction decals as necessary.
• To guard against engine over-heating, always have engine
debris filter mounted and clean.
• Inspect engine before storage. When not in use, disconnect
spark plug lead and store indoors in a dry place locked or
otherwise inaccessible to children.
• Use only original equipment parts from Rapala, including all
nuts and bolts.
StEPS fOR WORkING ON ENGINE OR AUGER
1. Turn off engine switch.
2. Disconnect the spark plug wire from the spark plug.
3. Securely place the disconnected spark plug wire away from
the spark plug and any metal parts. This must always be done
or arcing may occur between spark plug wire and metal parts.
4. Replace or repair the part on the engine or auger.
5. Check all parts that were repaired, or removed during repair,
that they are secure and fit correctly.
NOTE: All repair parts must come from the factory. Never
replace parts that are not specifically designed for the
engine or auger.
6. Reconnect spark plug wire to the spark plug.
PRE-OPERAtION
PREPARING ENGINE fOR StARtING
Before starting your unit, make sure the black throttle cable
housing is seated all the way into the brass ferrule at the engine
side of the cable.
GAS AND OIL
Quality
To operate the engine, we recommend using Viper® brand 2-cycle
oil (p/N 300400) to ensure that the engine operates correctly
throughout the life of the engine. Viper® brand 2-cycle oil has
fuel stabilizer additive which helps to prevent gasoline from
oxidizing and gumming up the carburetor when the unit is not
in use for long periods of time. Use unleaded regular gas only.
It is best to use premium gasoline that has no ethanol content.
Mixture
Run ice auger with a 50:1 ratio.
MIxING fUEL AND fILLING fUEL tANk
Mixing fuel
1. Fuel must be mixed in a container outside in a well ventilated
area.
2. Fill certified fuel container 1/4 full of recommended fuel.
3. Add recommended amount of 2 cycle oil with fuel stabilizer.
4. Screw container cap on straight and tight.
5. Shake the container to mix fuel and oil.
6. Wipe away any spilled fuel or oil and allow to evaporate before
moving or transporting.
filling fuel tank
1. Shut-off engine and allow engine to completely cool before
refilling the fuel tank.
2. Move to a well ventilated area, outdoors, away from flames
and sparks.
3. Clean debris from area around the fuel cap.
4. Loosen fuel cap slowly. place the cap on a clean, dry surface.
5. Carefully add fuel without spilling.
6. Do not fill fuel tank completely full, allow space for fuel to
expand.
7. Immediately replace fuel cap and tighten. Wipe off spilled
fuel and allow to dry before starting engine.
GAS
OIL
RAtIO
1 gallon
2.5 ounces
50:1
2 gallons
5 ounces
50:1
5 gallons
13 ounces
50:1
IMPORtANt
tHIS ENGINE USES A GAS/OIL MIxtURE. DO NOt RUN ON
StRAIGHt GAS ONLy, ENGINE DAMAGE WILL RESULt.
