background image

2-Ton Long-Reach Floor Jack 

4

 

P/N 5900387 — Rev. B2 — May 2020 

 

After lifting the Vehicle, you must support the load with appropriately-rated Vehicle support stands 
(such as Jack Stands) 

before

 you begin working on the Vehicle. 

 

The product should only be operated by authorized personnel. Keep children and untrained 
personnel away from the product. 

 

Keep hands and body away from all pinch points. 

 

When using the product, wear appropriate work clothes and ANSI-approved safety goggles. 

 

Do not make any modifications to the product; this voids your warranty. 

 

Make sure all operators read and understand the 

Installation and Operation Manual

. Keep the 

manual near the device at all times. 

 

Make a visual inspection of the product before using it. Do not use the product if you find any 

missing or damaged parts. Instead, take the unit out of service, then contact an authorized repair 

facility, your distributor, or Ranger Products at 

(800) 253-2363

Symbols 

Following are the symbols used in this manual: 

 

DANGER

 

Calls attention to a hazard that 

will

 result in death or injury. 

 

WARNING

 

Calls attention to a hazard or unsafe practice that 

could

 result in death or injury. 

 

CAUTION

 

Calls attention to a hazard or unsafe practice that could result in personal injury, 
product damage, or property damage. 

Liability Information 

BendPak Ranger assumes 

no

 liability for damages resulting from: 

•  Use of the equipment for purposes other than those described in this manual. 
•  Modifications to the equipment without prior, written permission from BendPak Ranger. 
•  Damage to the equipment from external influences. 
•  Incorrect operation of the equipment. 

 

 

Summary of Contents for RFJ-2TX













Reviews: