background image

5

ArtNo.090-0002 90 Griddle position

ArtNo.090-0004 Incorrect griddle position

ArtNo.311-0006 Correct wok sizes

The Wok Cradle 

(optional)

 

The wok cradle is designed to fit a 35 cm wok. If you use a 

different wok, make sure that it fits the cradle. Woks vary very 

widely in size and shape. It is important that the wok sits 

down on the pan support – however, if the wok is too small, 

the cradle will not support it properly 

(Fig.2-9)

.

The cradle should be used on the wok burner only. When you 

fit the cradle, make sure that it is supported properly on a pan 

support and the wok is sitting level in the cradle 

(Fig.2-10)

.

The cradle will get very hot in use – allow plenty of time for it 

to cool before you pick it up.

The Griddle 

(optional)

The griddle fits the left-hand pan support, front to back 

(Fig.2-11)

. It is designed for cooking food on directly. DO NOT 

use pans of any kind on it. The griddle surface is non-stick and 

metal cooking utensils (e.g. spatulas) will damage the surface. 

Use heat resistant plastic or wooden utensils.

n

n

DO NOT put it crossways – it will not fit properly and 

will be unstable (Fig.2-12).

n

n

DO NOT put it on any other burner – it is not 

designed to fit in any of the other pan supports.

Position the griddle over the hotplate burners resting on the 

pan support. Check that it is securely located.
The griddle can be lightly brushed with cooking oil before 

use

 (Fig.2-13)

. Light the hotplate burners. Adjust the flame 

heights to suit.
Preheat the griddle for 

a maximum of 5 minutes

 before 

adding food. Leaving it longer may cause damage. Turn the 

control knobs towards the low position, marked with the 

small flame symbol, to reduce the burner flames.

n

n

Always leave space around the griddle for the gases 

to escape.

n

n

NEVER fit two griddles side by side (Fig.2-14).

After cooking, allow the griddle to cool before cleaning.

Fig.2-11

Fig.2-12

Fig.2-9

ArtNo.311-0007 Wok stand close-up

Fig.2-10

ArtNo.311-0009 Oil on griddle 

Fig.2-13

ArtNo.311-0008 Griddle positioning

Fig.2-14

Summary of Contents for 100 Dual Fuel





































Reviews: