Range Master Classic C-45G3CB 463441412 Product Manual Download Page 11

11

Safety Tips

s

Before opening LP cylinder valve, check the coupling nut for 
tightness.

s

When grill is not in use, turn off all control knobs and LP 
cylinder valve. 

s

Never move grill while in operation or still hot.

s

Use long-handled barbecue utensils and oven mitts to avoid 
burns and splatters.

s

Maximum load for sideburner and side shelf is 10 lbs.

s

s

 

Clean grill often, preferably after each cookout. If a bristle

brush is used to clean any of the grill cooking surfaces,

ensure no loose bristles remain on cooking surfaces prior to
grilling. It is not recommended to clean cooking surfaces
while grill is hot.

s

If you notice grease or other hot material dripping from grill 
onto valve, hose or regulator, turn off gas supply at once. 
Determine the cause, correct it, then clean and inspect valve, 
hose and regulator before continuing. Perform a leak test.

s

Keep ventilation openings in cylinder enclosure (grill cart) free 
and clear of debris.

s

Do not store objects or materials inside the grill cart 
enclosure that would block the flow of combustion air to the 
underside of either the control panel or the firebox bowl.

s

The regulator may make a humming or whistling noise during 
operation. This will not affect safety or use of grill.

s

If you have a grill problem see the 

"Troubleshooting Section"

.

s

If the regulator frosts, turn off grill and LP cylinder valve 
immediately. This indicates a problem with the cylinder and it 
should not be used on any product. Return to supplier!

Ignitor Lighting

s

 

 Do not lean over grill while lighting.

1.
2.
3.
4.
5.

Turn 

OFF

 gas burner control valves. 

Turn 

ON

 gas at LP cylinder.

Open lid during lighting.

To ignite, push and turn ignition burner knob to 

HI

lights.

6. 

If ignition does NOT occur in 5 seconds, turn the burner 

controls 

OFF

, wait 5 minutes and repeat the lighting 

procedure.

7.

 To ignite remaining burners, turn knob to the 

HI

 position 

starting with the burners closest to IGNITION BURNERS first.
If ignitor does not work, follow match lighting instructions. 

P

. ush and hold 

ELECTRONIC IGNITION

 button until the burner 

Lighting instructions are continued on the next page

WARNING

For Safe Use of Your Grill and to Avoid Serious 
Injury:

Do not let children operate or play near grill. 

Keep grill area clear and free from materials that burn.

Do not block holes in sides or back of grill. 

Check burner flames regularly.

Use grill only in well-ventilated space. NEVER use in 
enclosed space such as carport, garage, porch, 
covered patio, or under an overhead structure of any 
kind.

Do not use charcoal or ceramic briquets in a gas grill. 
(

Unless

 

briquets are supplied with your grill.)

• Use grill at least 3 ft. from any wall or surface. 

Maintain 10 ft. clearance to objects that can catch fire 
or sources of ignition such as pilot lights on water 
heaters, live electrical appliances, etc.

• Apartment Dwellers:

Check with management to learn the requirements 
and fire codes for using an LP gas grill in your 
apartment complex. If allowed, use outside on the 
ground floor with a three (3) foot clearance from walls 
or rails. Do not use on or under balconies.

• NEVER attempt to light burner with lid closed. A 

buildup of non-ignited gas inside a closed grill is 
hazardous.

• Never operate grill with LP cylinder out of correct 

position specified in assembly instructions. 

• Always close LP cylinder valve and remove 

coupling nut before moving LP cylinder from 
specified operation position.

Do not cover grates with aluminum foil or any other
material.  This will block burner ventilation and create
a potentially dangerous condition resulting in 
property damage and/or personal injury.

CAUTION

• Putting out grease fires by closing the lid is not possible. 

Grills are well ventilated for safety reasons. 

• Do not use water on a grease fire. Personal injury may 

result. If a grease fire develops, turn knobs and LP 
cylinder off. 

• Do not leave grill unattended while preheating or burning 

off food residue on HI. If grill has not been regularly 
cleaned, a grease fire can occur that may damage the 
product. Follow instructions on General Grill Cleaning
and Cleaning The Burner Assembly to prevent grease fires.

The grease tray or cup  

must 

be installed during use and 

 emptied after each use. Do not remove grease tray or cup 

until grill has completely cooled.

Summary of Contents for Classic C-45G3CB 463441412





























Reviews: