background image

Remote-Control Commands

R&S

®

SMBVB-K548

20

User Manual 1179.0922.02 ─ 01

Parameters:

<ArbCfrSignalBw>

float
Range: 

0  to  depends on the sample rate of the loaded file

Increment:  0.1
*RST: 

250E6

Example: 

See 

Example "Configuring the CFR"

 

on page 16.

Manual operation: 

See 

"Signal Bandwidth"

 

on page 13

[:SOURce<hw>]:BB:ARBitrary:CFR:SFReq 

<ArbCfrStopBFreq>

Sets the stopband frequency of the filter, if 

[:SOURce<hw>]:BB:ARBitrary:CFR:

FILTer

 is set to 

ENHanced

. Frequency components higher than the stopband fre-

quency are filtered out by the lowpass filter.

Parameters:

<ArbCfrStopBFreq> float

Range: 

0  to  depends on the sample rate of the loaded file

Increment:  0.1
*RST: 

250E6

Example: 

See 

Example "Setting up an Enhanced Filter"

 

on page 16.

Manual operation: 

See 

"Stopband Freqeuncy"

 

on page 14

[:SOURce<hw>]:BB:ARBitrary:CFR:WAVeform:CREate 

<CreateWvFile>

With enabled signal generation, triggers the instrument to store the current settings in a
waveform file. Waveform files can be further processed.

The filename and the directory it is stored in are user-definable; the predefined file
extension for waveform files is 

*.wv

.

Setting parameters: 

<CreateWvFile>

string

Example: 

See 

Example "Configuring the CFR"

 

on page 16.

Usage: 

Setting only

Manual operation: 

See 

"Generate Waveform"

 

on page 12

Summary of Contents for SMBVB-K548























Reviews: