R&S EB500 Getting Started Download Page 56

Page: 56 / 70

Software and Firmware Update

R&S

EB500

Getting Started 4072.8432.02 ─ 04

Remote GUI on Notebook / desktop PC

If you want to install the GUI for use on a notebook or desktop PC, you should
follow the procedure described in

chapter 4.4, "GUI Installation for Remote

Access"

, on page 63.

If the R&S

EB500 cannot reboot

Due to the fact that the R&S

EB500 also can be updated using the Update32

Tool (see

"Updating the EB500 with front control panel"

on page 63), there

is a chance that the R&S

EB500 cannot reboot. Follow the steps described

"If the R&S

EB500 cannot reboot"

on page 63 to deal with this problem.

4.3

Receiver Firmware Update for EB500 without
front control panel

This model requires a different update method which makes use of the LAN inter-
face of the R&S

EB500 (X7 on the rear panel). The method uses the "Update32"

tool, which runs under Windows NT, Windows 2000 and Windows XP.

Retrieve Update32

The firmware required for the update can be retrieved from either one of the loca-
tions mentioned at

"CD-ROM and Downloads"

on page 48.

Click on

Firmware Update Program

and

File Explorer

will be launched into

the directory

Update32XP

. The

Update32

tool can be installed by clicking on

Setup

. If your browser does not launch

File Explorer

, you should launch it

manually and navigate to the

Update32XP

directory on the CD-ROM where you

can run

Setup

Receiver Firmware Update for EB500 without front control panel

Summary of Contents for EB500







































































Search results

Summary of Contents for EB500

Reviews:

Related manuals for EB500

Brands by name

Popular brands

R&S EB500, Getting Started

Search results

Summary of Contents for EB500

Reviews:

Related manuals for EB500

Brands by name

Popular brands