R&S CMW-KG4 Series User Manual Download

Page: 163 / 988

WCDMA Signaling

R&S

CMW-KG4xx/-KM4xx/-KS4xx

163

User Manual 1173.9657.02 ─ 11

Option R&S CMW-KS411 is required.

Remote command:

Unscheduled Subframes

Defines the transmission in the gaps between consecutive HS-SCCH subframes allo-
cated to the UE (inter-TTI distance > 1).

Option R&S CMW-KS411 is required.

●

Transmit Dummy UEID

: The HS-SCCH power is maintained and the unscheduled

HS-SCCH subframe contains the defined dummy UE ID, see

UE ID Dummy

●

DTX

: Discontinuous transmission in unscheduled HS-SCCH subframes (output

power switched off)

Remote command:

Example for cyclic HS-SCCH selection (R5 connection)

Settings:

●

HS-SCCH #1: Level = –7 dB

●

HS-SCCH #2: Level = OFF

●

HS-SCCH #3: Level = –7 dB

●

HS-SCCH #4: Level = OFF

●

Selection = Cyclic/Automatic

●

Number of HSSCCH = 3

●

Inter TTI = 2 configured in HSDPA channel configuration, see

chapter 2.4.13,

"HSDPA Settings"

on page 202

As a result of these settings, the HS-SCCH subframes 0 to 4 of the first two radio
frames are generated as follows:

●

Subframe 0: UE ID on HS-SCCH #1

●

Subframe 1: UE unscheduled due to Inter TTI = 2

●

Subframe 2: UE ID on HS-SCCH #2, but signal power off. UE returns DTX instead
of ACK or NACK.

●

Subframe 3: UE unscheduled

●

Subframe 4: UE ID on HS-SCCH #3

●

Subframe 0: UE unscheduled

●

Subframe 1: UE ID on HS-SCCH #1

●

Subframe 2: UE unscheduled

●

Subframe 3: UE ID on HS-SCCH #2, but signal power off. UE returns DTX instead
of ACK or NACK.

●

Subframe 4: UE unscheduled

2.4.9.4

HS-PDSCH Configuration

This section configures the HS-PDSCH.

For a dual carrier scenario, all settings are available per carrier. For switching between
the carriers see

"Select Carrier"

on page 155.

GUI Reference

深圳德标仪器

135-1095-0799

Summary of Contents for CMW-KG4 Series





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for CMW-KG4 Series

Reviews:

Related manuals for CMW-KG4 Series

Brands by name

Popular brands

R&S CMW-KG4 Series, User Manual

Search results

Summary of Contents for CMW-KG4 Series

Reviews:

Related manuals for CMW-KG4 Series

Brands by name

Popular brands