Page
6
of
9
HSH0001BK
R&G
Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
NOTICE DE MONTAGE
Note: Si vous utilisez les clignotants d’origine, il doit y avoir une protection chaleur (article 1) montée sur le clignotant côté droit
pour protéger le clignotant de la chaleur émise par le pot d’échappement.
•
Si le support de plaque a déjà été monté sur la moto, enlever le siège puis débrancher le feu de plaque R&G et les clignotants
du faisceau de câble, en notant la correspondance des connecteurs.
•
Enlever les 4 boulons indiqués sur la Photo 1, tirer doucement le morceau de caoutchouc (voir Photo 2) et le fil à travers, puis
enlever le support de plaque de la moto.
•
Enlever le clignotant requis pour installer la protection chaleur, pour cela vous aurez peut-être besoin de retirer le collier de
serrage, voir Photo 3.
•
Enlever le feu de plaque R&G de son support.
•
Monter le clignotant sur le support R&G en passant le filetage au bas du clignotant dans le support (et à travers la protection
chaleur [article 1]), puis fixer la position en réutilisant les rondelles d’origine et écrous, voir photo 4.
•
Remonter le feu de plaque R&G sur le support de plaque, voir photo 4.
•
Remonter les caches fils de clignotants, voir photo 5.
•
Passer les fils dans l’ouverture, voir Photo 2, puis replacer le morceau en caoutchouc.
•
Reconnecter le feu de plaque R&G et les clignotants sur le faisceau de câbles.
•
Remonter le support de plaque R&G sur la moto, en utilisant les 4 boulons, voir Photo 1.
ISSUE 1 06/11/2018 (LF)
Notice disponible au téléchargement sur
www.rg-racing.com
CONSUMER NOTICE
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design changes which do not diminish their
performance or visual appeal and supplying them in such state shall conform to the order. The Buyer acknowledges no representation or warranty (other than as to title)
has been given or will apply to the Products other than those in R&G’s order or confirmation and the Buyer confirms it has chosen the Products as being of
merchantable quality and suitable for its particular purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable skill and care and
rectify any fault free of charge unless the workmanship has been disturbed. The Buyer is responsible for ensuring that the warranty on the motorcycle is not affected by
the fitting of the Products. On return of any defective Products R&G shall at its option either supply a replacement or refund the purchase money but shall not be liable
if the Products have been modified or used or maintained otherwise than in accordance with R&G’s or manufacturer’s instructions and good engineering practice or if
the defect arises from accident or neglect. Other than identified above and subject to R&G not limiting its liability for causing death and personal injury, it shall not be
liable for indirect or consequential loss and otherwise its liability shall be limited to the amounts paid by the Buyer for the Products or the fitting or service concerned.
These terms do not affect the Buyer’s statutory rights.
R&G RETURNS POLICY (NON-FAULTY GOODS)
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they were purchased direct from us
(customer must prove if necessary). Otherwise to be returned to original vendor. Goods must be in re-sellable condition, in the opinion of R&G. All returns are subject
to a 25% restocking and handling fee (25% of the gross value exc. P&P – at the prevailing price at time of purchase). The customer must pay any and all carriage
charges. No returns of discontinued products, unless within 14 days of purchase. This policy does not affect your statutory rights and does not refer to faulty goods.
