Ranco ETC-111000 Quick Start Manual Download Page 7

Replacement Sensor - Order

Part No. 1309001-044

The 1309007-044 sensor is a negative temperature coefficient
(NTC) thermistor sensor. The sensor resistance decreases with
temperature increase.

It is .25 x 1.94 long with 8 feet #22 AWG

cable. The thermistor has a reference resistance of 30,000 ohms

at 770f (25OC).

IMPORTANT

The schematic drawings and other information induded in these instruc-
tions are forthe purpose of illustration andgeoern.l reference only. Ranco
assumes no responsibility

for any uncooventionaJ application of this

control, unless such application has been approved in writing by Ranco.

Deg.c.

Deg.F.

RES. Nom.

-40

-40

1,010,000

-30

-22

531,000

-20

-4

291,200

-10

14

166,000

0

32

97,960

10

50

59,700

20

68

37,470

25

77

30,000

30

86

24,170

40

104

15,980

50

122

10,810

60

140

7,464

70

158

5,200

80

176

3,774

90

194

2,753

100

212

2,036

110

230

1,531

Figure 10:

Resistance

vs

Temperature of 1309007-044.

Sensor including 8 foot cable.

Ranco North America

8115 U.S. Rt. 42 North

Plain City, Ohio 43064

~

An Invensys Company

Summary of Contents for ETC-111000








Reviews: