background image

WSR-ANT 

 18  

The Ramsey Kit Warranty

 

 

Please read carefully BEFORE calling or writing in about your kit. 
Most problems can be solved without contacting the factory.

 

 
Notice that this is not a "fine print" warranty. We want you to understand 
your rights and ours too! All Ramsey kits will work if assembled properly. 
The very fact that your kit includes this new manual is your assurance 
that a team of knowledgeable people have field-tested several "copies" 
of this kit straight from the Ramsey Inventory. If you need help, please 
read through your manual carefully, all information required to properly 
build and test your kit is contained within the pages!   
 

1. DEFECTIVE PARTS:

 It's always easy to blame a part for a problem in 

your kit, Before you conclude that a part may be bad, thoroughly check 
your work. Today's semiconductors and passive components have 
reached incredibly high reliability levels, and it’s sad to say that our 
human construction skills have not! But on rare occasions a sour 
component can slip through. All our kit parts carry the Ramsey 
Electronics Warranty that they are free from  defects for a full ninety (90) 
days from the date of purchase. Defective parts will be replaced 
promptly at our expense. If you suspect any part to be defective, please 
mail it to our factory for testing and replacement. Please  send only the 
defective part(s), not the entire kit. The part(s) MUST be returned to us 
in suitable condition for testing. Please be aware that testing can usually 
determine if the part was truly defective or damaged by assembly or 
usage. Don't be afraid of telling us that you 'blew-it', we're all human and 
in most cases, replacement parts are very reasonably priced.   
 

2. MISSING PARTS:

 Before assuming a part value is incorrect, check 

the parts listing carefully to see if it is a critical value such as a specific 
coil or IC, or whether a RANGE of values is suitable (such as "100 to 
500 uF"). Often times, common sense will solve a mysterious missing 
part problem. If you're missing five 10K ohm resistors and received five 
extra 1K resistors, you can pretty much be assured that the '1K ohm' 
resistors are actually the 'missing' 10 K parts ("Hum-m-m, I guess the 
'red' band really does look orange!")  Ramsey Electronics project kits are 
packed with pride in the USA. If you believe we packed an incorrect part 
or omitted a part clearly indicated in your assembly manual as supplied 
with the basic kit by Ramsey, please write or call us with information on 
the part you need and proof of kit purchase 

Summary of Contents for WSR-ANT





















Reviews: