background image

FR-220 

 12 

 
Also, if you plan to use an enclosure other than the custom Ramsey 
enclosure and knob kit, you may wish to locate the controls differently 
than provided by the PC board. In this case, the control lugs are wired to 
the PC board using your own insulated hookup wire, kept as short as 
possible for neat installation.    
 

FURTHER COMPONENT INSTALLATION 

  

 

All "directions" on the PC board (i.e.: right, left, above, below and so 
forth)  assume orientation of your board as shown in the parts layout 
diagram. Therefore the rear of the board (connectors) is the lower end, 
and the front (controls) is the upper end. 
 

1. ANTENNA INPUT AND TUNED RF PREAMPLIFIER 

    

5.    Install C1, 4.7 or 5 pf disc capacitor. 

6.    Install C2, 2 or 2.2 pf. 

7.    Install C3, 10 pf. 

8.    Install L1, a small 4 turn wire coil. Gently stretch the coil just 
enough so that it's two wire leads fit firmly into the PC board holes. 
Solder both leads securely. This coil is designed to permit additional  
stretching or compressing as part of the alignment process. 

9.    Install C4, 10 pf. 

10. Install L2, the other 4 turn coil just like L1 above. 

11. Install C5, 4.7 or 5 pf. 

12. Clearly identify Q1, the 2SC2498 or 2SC2570A transistor. Do not 
confuse it with the other transistors supplied. 

13. Position Q1 as shown on the PC board layout, with the flat side 
facing to the right, toward the middle of the board. Press the 
transistor snugly into the PC board so that only a minimum amount 
of wire  lead is exposed above the board. In soldering, don't be 
afraid to use enough heat to make good clean connections. 

14. Install R4, 47K, just to the left of Q1 [yellow-violet-orange]. 

15. Install C6, 100 pf (marked 100 or 101). 

Summary of Contents for FR220





























Reviews: