RAM 1500 2023 Page 174 Owner'S Manual Download

Page: 174 / 416

172

STARTING AND OPERATING

VEHICLE LOADING

ROSS

EHICLE

EIGHT

ATING

(GVWR)

The GVWR is the total permissible weight of your vehicle

including driver, passengers, vehicle, options and cargo.

The label also specifies maximum capacities of front and

rear Gross Axle Weight Rating (GAWR). Total load must be

limited so GVWR and front and rear GAWR are not

exceeded.

AYLOAD

The payload of a vehicle is defined as the allowable load

weight a truck can carry, including the weight of the driver,

all passengers, options and cargo.

ROSS

XLE

EIGHT

ATING

(GAWR)

The GAWR is the maximum permissible load on the front

and rear axles. The load must be distributed in the cargo

area so that the GAWR of each axle is not exceeded.
Each axle GAWR is determined by the components in the

system with the lowest load carrying capacity (axle,

springs, tires or wheels). Heavier axles, or suspension

components sometimes specified by purchasers for

increased durability, do not necessarily increase the

vehicle's GVWR.

IRE

IZE

The tire size on the Vehicle Certification Label represents

the actual tire size on your vehicle. Replacement tires

must be equal to the load capacity of this tire size.

IZE

This is the rim size that is appropriate for the tire size

listed.

NFLATION

RESSURE

This is the cold tire inflation pressure for your vehicle for

all loading conditions up to full Gross Axle Weight Rating

(GAWR).

URB

EIGHT

The curb weight of a vehicle is defined as the total weight

of the vehicle with all fluids, including vehicle fuel, at full

capacity conditions, and with no occupants or cargo

loaded into the vehicle. The front and rear curb weight

values are determined by weighing your vehicle on a

commercial scale before any occupants or cargo are

added.

OADING

The actual total weight and the weight of the front and rear

of your vehicle at the ground can best be determined by

weighing it when it is loaded and ready for operation.

The entire vehicle should first be weighed on a commercial

scale to ensure that the Gross Vehicle Weight Rating

(GVWR) has not been exceeded. The weight on the front

and rear of the vehicle should then be determined

separately to be sure that the load is properly distributed

over the front and rear axle. Weighing the vehicle may

show that the Gross Axle Weight Rating (GAWR) of either

the front or rear axles has been exceeded but the total

load is within the specified GVWR. If so, weight must be

shifted from front to rear or rear to front as appropriate

until the specified weight limitations are met. Store the

heavier items down low and be sure that the weight is

distributed equally. Stow all loose items securely before

driving.
Improper weight distributions can have an adverse effect

on the way your vehicle steers and handles and the way

the brakes operate.

WARNING!

Do not load your vehicle any heavier than the GVWR or

the maximum front and rear GAWR. If you do, parts on

your vehicle can break, or it can change the way your

vehicle handles. This could cause you to lose control.

Overloading can shorten the life of your vehicle.

23_DT_OM_EN_USC_t.book Page 172

Summary of Contents for 1500 2023

































































































































































































































































































































































































































Search results

Summary of Contents for 1500 2023

Reviews:

Related manuals for 1500 2023

Brands by name

Popular brands

RAM 1500 2023, Owner'S Manual

Search results

Summary of Contents for 1500 2023

Reviews:

Related manuals for 1500 2023

Brands by name

Popular brands