NO.
NO.
1
36
2
37
38
3.
39
4
40
5
41
4.
6
42
7
43
8
44
5.
9
45
10
46
6.
11
47
12
48
7.
13
49
14
50
•
15
51
16
52
•
17
53
18
54
•
19
55
20
56
21
57
58
59
23
60
24
25
62
63
27
64
28
65
29
66
30
67
31
68
32
34
35
71
3
4
Perhaps change/replace every year or inspect once a year for wear. It is
suggested to tape these to the bottom of the controller and date it. For
the laboratory, it is easier and only a few minutes to replace and
maintain once a year as a minimal low cost maintenance. In the
operatory area, every 2-3 years should be adequate.
61
CARBON BRUSH
SPRING
PRIMUS 45 SPINDLE
ASSEMBLY
26
33
MOVING HOUSING
SPRING
SET RING TEFLON
WASHER
SNAP RING
1030 FIX O-RING
MOTOR CASE
MOTOR CASE BOLT
COIL
WEDGE
FAN
830 SPACER
BRUSH HOLDER
CARBON BRUSH
CARBON BRUSH CAP
TERMINAL (L)
69
CARBON HOUSING
COVER
70
MOVING HOUSING
MOTOR CASE COVER
BEARING BUSH COLLAR
BH60 CONNECTOR
SET RING
SET RING INSERT
CAM TEFLON WASHER
CAM
CAM BALL
M2.5
PARTS LIST FOR FOR PRIMUS 45 HANDPIECE
3
CHUCK HOUSING C-
RING
1370 WAVE WASHER
BH60 O-RING
22
BEARING BUSH COLLAR
WASHER
SET RING WASHER
PARTS NAME
HAND CAP COVER
HAND CAP HEAD
Never use chemicals for cleaning as often they are harsh and can
corrode parts. Use only isopropyl alcohol in either sealed wipes or with a
tissue to clean the exterior and any dust or debris that has accumulated.
BALL BEARING(1040ZZ)
Warranty is valid within the United States only.
HANDPIECES
— These products are under warranty for a period of SIX
MONTHS from the date of original installation by the purchaser. IT DOES
NOT COVER MISUSE, NORMAL BEARING, OR CARBON BRUSH WEAR.
IN HOUSE OR FACTORY REPAIR - WARRANTY CLAIMS
—
Please visit our website,
www.ramprodinc.com
, to download the
Customer
Service Request Form
located at the top right of the website page. For
warranty claims, please include a copy of your invoice or reference purchase
date. Repairs carry a 90 day warranty.
We maintain parts for Ram and many other similar models to perform service.
When sending items for service please pack it well with proper protection.
It is your responsibility to get the unit to us. Return shipping and handling is
covered by Ram Products, Inc.
1040 COPPER WASHER
1040 TEFLON WASHER
PARTS NAME
SM110 MAGNET GUIDE
COPPER WASHER
1030 WAVE WASHER
After sterilization of burs make sure they are completely dry and avoid
getting chemicals / disinfectants inside the handpiece.
For cleaning, it is suggested once a week to use a can of compressed
air often sold at office supply, computer supply stores. (The compressed
air at the bench is high pressure and can not only push any dust or dirt
inside further but also can upset the small balls that are part of the
bearings which are the life line of the handpiece.
WARRANTY PERIOD
PRODUCT WARRANTY
COLLAR
BEARING FIX WASHER
1370 WASHER
BALL BEARING(1370ZZ)
HAND CAP BODY
Use good quality burs. Do not force any burs into the chuck, make sure
burs are not eccentric. If any rust on the bur shaft, it is best to discard.
Always leave a bur securely locked in the handpiece. Wait for the
handpiece to stop spinning before changing burs.
SM110 MAGNET C
TERMINAL (R)
CARBON BRUSH BOLT
TEFLON WASHER
BEARING HOUSING
BACK BEARING SIT
BALL BEARING 1030ZZ
BR BRUSH BOLT
BALL BEARING(1480ZZ)
1480 WASHER
1480 WAVE WASHER
TEST BUR
CHUCK SPRING
JOINT SHAFT BODY
JOINT SHAFT
JOINT SHAFT FIX PIN
Electric lab handpieces have grease sealed ball bearings. Please do not
oil as you would air or high-speed handpieces as this would break down
the grease sealed bearings.
1040 SPACER
SHAFT Ø4
CORE
FRONT SHAFT BUSH Ø4
COMMUTATOR
COLLET CHUCK 2.35
CHUCK HOUSING
BUSH
In order to validate your warranty, the form must be filled out
completely on the website:
www.ramprodinc.com/warranty
within
10 days of purchase/installation.
Electrical and mechanical equipments which are mishandled, used incorrectly,
and/or used for a purpose other than that for which they were designed and
intended, will void the product warranty.
WARRANTY CLAIMS
All returned items shall be free from defects/alterations in material,
workmanship and original product design.
The product shall have been used under the conditions for which it has
been intended, and in a manner for which it has been designed.
The customer must maintain the product as specified within the
individual product instruction booklet.
The product shall have been operated in a manner for which it was
intended and in the proper environmental conditions.
Should your product require service within the warranty period, we will elect to
make the necessary repair or replacement at no charge including return
shipping. It is your responsibility to return the product to Ram Products and it
is recommended that returns have tracking information and to be adequately
insured against carrier loss or damage.
All claims should describe the specific problem for accurate analysis and
evaluation, the return date of the warranty card along with the supply house
and/or dealer name.
WARRANTY REGISTRATION
MOTOR CORD
ARMATURE ASSEMBLY