Rally URCap User Manual Download | Manualshive

Page: 41 / 117

background image

6.1.3 - Gripper

Choose the gripper type according to the gripper mounted on the robot. The following
options are available.

Schmalz FXCB - Foam and Schmalz FXCB - Suction cups

Choose this option if a Schmalz FXCB Foam gripper or a Schmalz FXCB Suction cup
gripper has been mounted on the robot. Once the type of gripper is set to one of these
Schmalz grippers, the IO channels, weight, and dimensions are predefined. The grip and
release functions are controlled by the Pally URCap via the tool digital IO channels.

Note:

Make sure the Tool IO voltage is properly set to 24V.

Note:

In order to get reliable feedback from the vacuum sensor, you need to configure the

SP2 and rP2 values according to the

Operating instructions for the vacuum switch VSi

UniGripper Co/Light

Choose this option for standard mounted Unigripper Co/Light gripper only, as weight and
dimensions are predefined. The grip and release functions are controlled by the Pally
URCap via the digital IO channels configured here.

Note:

Only choose this option if your gripper is standard mounted, i.e. without any offset

plates and custom rotations. In all other cases, choose the "Other vacuum gripper" option.

Custom Vacuum Gripper

Choose this option for other vacuum grippers that can be controlled by simple digital IO
signals. Weight and dimensions of the gripper must be manually entered using this option.
The grip and release functions are controlled by the Pally URCap via the digital IO channels
configured here.

Custom Gripper

Choose this option if the gripper has its own URCap to control grip and release functions.
Weight and dimensions of the gripper must be manually entered using this option. See

for further details on inserting custom commands into the program sequence.

Version 2.9.1

© Rocketfarm AS 2021. All rights reserved.

41

«
...
39
40
41
42
43
...
»

Summary of Contents for URCap






















































































































Reviews:

No comments

Related manuals for URCap

Brand: Adance Pages: 50

WSAT-SC 100D Series

Brand: CLIVET Pages: 50

Brand: Lorenz Pages: 30

York YKEP Series

Brand: Johnson Controls Pages: 128

Brand: Kaysun Pages: 56

Brand: EarthQuake Pages: 24

Brand: Troy-Bilt Pages: 19

CWW 18/C Series

Brand: Clint Pages: 10

Brand: Iom Pages: 49

Brand: breviglieri Pages: 33

Hyperchill ICE003

Brand: Parker Hiross Pages: 28

Brand: Scheppach Pages: 156

Brand: EINHELL Pages: 255

Brand: Daikin McQuay Pages: 216

Brand: Emerson Pages: 20

Millennium YCAS Series

Brand: York Pages: 188

Brand: Ecoboil Pages: 4

Brand: Qualcast Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands