background image

2021 RALE® ST120 INSTALLATION GUIDE

2

2021 RALE® ST120 INSTALLATION GUIDE

2

WARNINGS

Please review and familiarize yourself with the following warnings 

and their meanings. They will be found throughout this Installation 

Guide.

DANGER

Potential of death, serious harm or injury to the operator or 

bystander(s).

CAUTION

Possible damage to the motorcycle, track adaption system or 

adjacent property.

NOTICE

Specific instructions requiring extra attention or important things 

to note.

NOTE: It is not possible for RALE to warn the owner or operator 

of every conceivable DANGER, CAUTION or NOTICE that may be 

encountered in relation to the RALE ST120. It is the responsibility of 

the owner and/or the operator to exercise good judgment to stay 

safe at all times 
DANGER: Cancer and Reproductive Harm www.P65Warrnngs.ca.gov
Before operating a vehicle equipped with a RALE Track Kit, all 

operators should read and become familiar with the User’s Manual. 

The  latest  digital  version  of  this  manual  can  be  found  online  at                                                  

www.riderale.com
The document number, version number and release date of this 

manual can be found on the inside cover. 

Summary of Contents for ST120 2021























Reviews: