Raisecom RC3000-15 Page 59 Hardware Description Download

Page: 59 / 273

Raisecom
RC3000-15 (P100R001) Hardware Description

4 DXC cards

Raisecom Proprietary and Confidential

4.2.5 Buttons

Table 4-20 lists buttons on the DXC card (E.30).

Table 4-20

Buttons on the DXC card (E.30)

Print

Button

Status

Description

–

Buzzer
control
button

MUTE

(Up)

In this status, when an alarm is being
generated, the buzzer is mute. You cannot
change this status through software.

RING

(Down)

In this status, when an alarm is being
generated, the buzzer rings. You can shield this
status through software.

4.2.6 LEDs

Table 4-21 lists LEDs on the DXC card (E.30).

Table 4-21

LEDs on the DXC card (E.30)

LED

Color

Description

PWR

Green

Power LED



Green: the power supply is normal.



Off: the power supply is abnormal.

SYS

Green

System status LED



Blinking green: the system is working properly.



Off: the system is working improperly.

ACT

Green

Working mode LED



Green: the card is the master.



Off: the card is the slave.

100M

(SNMP)

Green

SNMP interface rate LED



Green: the Ethernet rate is 100 Mbit/s.



Off: the Ethernet rate is 10 Mbit/s or the interface is
disconnected.

LNK/ACT

(SNMP)

Green

SNMP interface working LED



Green: the SNMP interface is working properly.



Off: the SNMP interface is disconnected or is working
improperly.



Blinking green: the SNMP interface is receiving or
sending data.

100M

(NM-EXT)

Green

NM-EXT interface rate LED



Green: the NM-EXT interface is working at 100 Mbit/s.



Off: the NM-EXT interface is working at 10 Mbit/s.

Summary of Contents for RC3000-15


















































































































































































































































































Search results

Summary of Contents for RC3000-15

Reviews:

Related manuals for RC3000-15

Brands by name

Popular brands

Raisecom RC3000-15, Hardware Description

Search results

Summary of Contents for RC3000-15

Reviews:

Related manuals for RC3000-15

Brands by name

Popular brands