Raisecom RC3000-15 Hardware Description Download

Page: 229 / 273

Raisecom
RC3000-15 (P100R001) Hardware Description

13 Cables

Raisecom Proprietary and Confidential

204

Figure 13-16

Appearance of the CBL-V24-HDB26M/4DB25M-D cable

13.10.3 PIN definitions

CBL-V24-HDB26M/4DB25F (DCE cable)

The CBL-V24-HDB26M/4DB25F cable is a DB26 male connector-to-4-way DB25 female
connector cable. It is used to connect the DTE (male connector).

Table 13-16

CBL-V24-HDB26M/4DB25F

Figure

HDB26M

PIN

DB25F PIN

Definition Channel

Direction

DTE→DCE DCE→DTE

HDB26M

DB25F

Connected
to the shell

Channel 1

RXD

√

TXD

√

TXC

√

RXC

SCTE

√

25, 26

Short
connected

RTS

√

CTS

√

Short
connected

DSR

√

DCD

√

Summary of Contents for RC3000-15


















































































































































































































































































Search results

Summary of Contents for RC3000-15

Reviews:

Related manuals for RC3000-15

Brands by name

Popular brands

Raisecom RC3000-15, Hardware Description

Search results

Summary of Contents for RC3000-15

Reviews:

Related manuals for RC3000-15

Brands by name

Popular brands