Raisecom RC3000-15 Page 181 Hardware Description Download

Page: 181 / 273

Raisecom
RC3000-15 (P100R001) Hardware Description

10 Data cards

Raisecom Proprietary and Confidential

156

When the FE electrical interface is configured to 10 Mbit/s through auto-negotiation
or manual configuration, it cannot transmit services.

10.6.5 LEDs

Table 10-33 lists LEDs on the HT-8FE16E1.

Table 10-33

LEDs on the HT-8FE16E1

LED

Color

Description

PWR

Green

Power LED



Green: the power supply is normal.



Off: the power supply is abnormal.

SYS

Green

System status LED



Blinking green: the system is working properly.



Off: the system is working improperly.

100M (1–8)

Green

FE electrical interface rate LED:



Green: the FE electrical interface is working at 100
Mbit/s.



Off: the FE electrical interface is working at 10 Mbit/s.

LNK/ACT (1–8)

Green

Link working LED



Green: the link interface is working properly.



Blinking green: the link interface is receiving or
sending data.



Off: the link interface is disconnected or is working
improperly.

10.6.6 Internal jumper

Table 10-34 lists the internal jumper used by the HT-8FE16E1.

Table 10-34

Internal jumper used by the HT-8FE16E1

Jumper

Function

Status

Description

JP101

Configure the
mode for
downloading
the MCU
program.

Short-circuited

Enter ISP mode. In this mode, the
RC3000-15 is waiting to be upgraded.
You can upgrade MCU program through
the serial interface on the backplane.

Disconnected

Enter normal working mode.



By default, JP101 is disconnected; namely, MCU is in normal working mode.

Summary of Contents for RC3000-15


















































































































































































































































































Search results

Summary of Contents for RC3000-15

Reviews:

Related manuals for RC3000-15

Brands by name

Popular brands

Raisecom RC3000-15, Hardware Description

Search results

Summary of Contents for RC3000-15

Reviews:

Related manuals for RC3000-15

Brands by name

Popular brands