Home
/
Raisecom
/
RC3000-15
/
Hardware Description

Raisecom RC3000-15, Hardware Description

Share

Page: 158 / 273

background image

Raisecom
RC3000-15 (P100R001) Hardware Description

10 Data cards

Raisecom Proprietary and Confidential

Copyright © Raisecom Technology Co., Ltd.

133

10.1 8ETHP

10.1.1 Functions and appearance

Panel

Function

The 8ETHP card, a service access card, supports 8 ways of dependent
Ethernet services. It transmits 8 ways of Ethernet (EoPDH) services
to 8 local Ethernet interfaces through the cross connection card. These
8 local Ethernet interfaces are independent of each other. The 8ETHP
card provides the following functions:



Provide 8 independent Ethernet interfaces.



Support configuring bandwidth of Ethernet interfaces to N×64 kbit/s
(N = 1–32). It does not support reverse multiplexing.



Support a maximum frame length of 2048 bytes.



Support 10/100 Mbit/s rate and half/full duplex auto-negotiation.



Support 802.3x and back pressure flow control.



Support loopback on each Ethernet interface.



Support traffic statistics.

«
...
156
157
158
159
160
...
»

Summary of Contents for RC3000-15


















































































































































































































































































Reviews:

No comments

Related manuals for RC3000-15

3255-50 HiTESTER

Brand: Hioki Pages: 52

Brand: ennoLogic Pages: 52

Brand: Clas Ohlson Pages: 4

Brand: Hanna Pages: 28

Brand: Owon Pages: 88

Brand: 3B SCIENTIFIC PHYSICS Pages: 42

Brand: Brymen Pages: 8

Brand: PeakTech Pages: 55

Brand: PeakTech Pages: 64

Brand: CTC Union Pages: 4

Brand: Hanna Instruments Pages: 46

Brand: Maxwell Digital Multimeters Pages: 6

Brand: Maxwell Digital Multimeters Pages: 8

Brand: Maxwell Digital Multimeters Pages: 20

Brand: Maxwell Digital Multimeters Pages: 24

Brand: YATO Pages: 52

Brand: Radio Shack Pages: 24

Brand: Kewtech Pages: 30

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands