Raisecom RC3000-15 Hardware Description Download

Page: 101 / 273

Raisecom
RC3000-15 (P100R001) Hardware Description

8 Voice cards

Raisecom Proprietary and Confidential

8.2.2 Version

Card

Slot

RC3000-15-FXS/FXO

8.2.3 Slots

Chassis version

Slot

E.30 and E.20

1–6 and 9–13

8.2.4 Interfaces

Interface type

Table 8-9 lists the interface on the FXS/FXO card.

Table 8-9

Interface on the FXS/FXO card

Name

Type

Description



1-4



5-8



9-12



13-16

RJ45 interface

Accessing up to 16 ways of FXS/FXO services,
with 4 ways occupying one RJ45 interface

Interface parameter

Table 8-10 lists parameters of the FXS/FXO card.

Table 8-10

Parameters of the FXS/FXO card

Parameter

Description

Coding scheme

A-law

Bit rate

64 kbit/s

Audio port impedance

On-hook impedance is 2 MΩ.

Off-hook loopback impedance is 600+200//0.1.

Effective transmission
bandwidth

300–3400 Hz/600 Ω

Gain frequency features

The Rx (A/D) gain ranges from -10 to +16 dB, and is 0 dB by
default. Its step is 0.1 dB.

Summary of Contents for RC3000-15


















































































































































































































































































Search results

Summary of Contents for RC3000-15

Reviews:

Related manuals for RC3000-15

Brands by name

Popular brands

Raisecom RC3000-15, Hardware Description

Search results

Summary of Contents for RC3000-15

Reviews:

Related manuals for RC3000-15

Brands by name

Popular brands