Raisecom iTN8600-I Product Description Download

Page: 33 / 71

Raisecom
iTN8600-I (A) Product Description

3 Cards and parts

Raisecom Proprietary and Confidential

Figure 3-4

Panel of the fan

3.4.3 Functions

Table 3-18

Functions of the fan

Function

Description

Basic functions



Each FANS383 is embedded with 2 fans.



Support hot swapping.



Each device must use 3 FANS383.



Support manually configuring the rotational speed to 4 gears.

Alarm
monitoring



Support speed feedback.



Support in-position monitoring.



Support fan fault alarms, including the alarm of decrease of the
rotational speed due to fan stopping rotating and fan aging.

3.5 Default configurations

Table 3-19 lists default configurations of the iTN8600-I-XT4D.

Table 3-19

Default configurations of the iTN8600-I-XT4D

Type

Default configuration

In-band NMS
channel



GCC0 is enabled on L1 and L2.



GCC0 of L1 and L2 is added to the bridge interface to support
automatic topology discovery.

Client-side
mapping mode

OTN



By default, no cross connection and protection are configured on the device.



For interfaces and services supported in client-side mapping mode, see Table 1-2.

Summary of Contents for iTN8600-I








































































Search results

Summary of Contents for iTN8600-I

Reviews:

Related manuals for iTN8600-I

Brands by name

Popular brands

Raisecom iTN8600-I, Product Description

Search results

Summary of Contents for iTN8600-I

Reviews:

Related manuals for iTN8600-I

Brands by name

Popular brands