manualshive.com logo in svg

Raisecom iTN2100, Hardware Description, Page: 77 / 312

Share
Download
Raisecom iTN2100 Hardware Description Download Page 77

Raisecom 
iTN2100 (P100R002) Hardware Description 

8 Ethernet aggregation card 

 

 

Raisecom Technology Co., Ltd. 

48 

 

Table 8-3

 

LEDs on the iTN2100-NTU-4GF 

LED 

Status 

Description 

PWR 

Green 

Power LED 

 

Green: the power supply is normal. 

 

Off: the power supply is abnormal. 

SYS 

Green 

System status LED 

 

Green: the system is working improperly. 

 

Off: the system is working improperly. 

 

Blinking green: the system is working properly. 

ACT 

Green 

Primary/Slave LED 

 

Green: the card is primary. 

 

Off: the card is slave. 

1000M 

(1–4) 

Green 

SFP optical interface 1000 Mbit/s LED 

 

Green: the Ethernet rate is 1000 Mbit/s. 

 

Off: the Ethernet rate is 100 Mbit/s or the connection fails. 

LNK/ACT 

(1–4) 

Green 

SFP optical interface working LED 

 

Green: the SFP optical interface is properly connected. 

 

Off: the SFP optical interface is improperly connected or 
disconnected. 

 

Blinking green: the SFP optical interface is receiving or 
sending data. 

 

8.1.5 Specifications 

Table 8-4 lists specifications of the iTN2100-NTU-4GF. 

Table 8-4

 

Specifications of the iTN2100-NTU-4GF 

Parameter 

Value 

Dimensions 

25 mm (width) × 232 mm (depth) × 240 mm (height) 

Weight 

0.52 kg 

Max. power consumption  26 W 

 

Summary of Contents for iTN2100

























































































































































































































































































































Reviews:

No comments