manualshive.com logo in svg

Raisecom iTN2100, Hardware Description, Page: 67 / 312

Share
Download
Raisecom iTN2100 Hardware Description Download Page 67

Raisecom 
iTN2100 (P100R002) Hardware Description 

7 SDH tributary cards 

 

 

Raisecom Technology Co., Ltd. 

38 

 

Parameter 

Description 

Line code 

NRZ 

Multiplexing structure 

Comply with ITU-T G.707 recommendations. 

Jitter 

Comply with ITU-T G.783 and ITU-T G.825 
recommendations. 

Optical interface parameters 

Comply with ITU-T G.957 recommendations. 

 

7.1.4 LEDs 

There are eight LEDs on the OPCOM3500E-STM1-S (Versions A and B) panel, as listed in 
Table 7-5. 

Table 7-5

 

LEDs on the OPCOM3500E-STM1-S (Versions A and B) panel 

LED 

Status 

Description 

PWR 

Green 

Power LED 

 

Green: the power supply is normal. 

 

Off: the power supply is abnormal. 

SYS 

Green 

System status LED 

 

Green: the system is working improperly. 

 

Off: the system is working improperly. 

 

Blinking green: the system is working properly. 

SWH 

Green 

Protection switchover LED 

 

Green: a switchover occurs. 

 

Off: no switchover occurs. 

ALM 

Red 

Alarm LED 

 

Red: MS-AIS, MS-EXC, AU-AIS, or AU-LOP alarms 
are generated. 

 

Off: no MS-AIS, MS-EXC, AU-AIS, or AU-LOP 
alarms are generated. 

LOF (A, B) 

Red 

LOF alarm LED 

 

Red: input LOF alarms are generated on optical 
interfaces. 

 

Off: no input LOF alarms are generated on optical 
interfaces. 

LOS (A, B) 

Red 

LOS alarm LED 

 

Red: input LOS alarms are generated on optical 
interfaces. 

 

Off: no input LOS alarms are generated on optical 
interfaces. 

 

There are six LEDs on the OPCOM3500E-STM1-S (Version C) panel, as listed in Table 7-6. 

Summary of Contents for iTN2100

























































































































































































































































































































Reviews:

No comments