Raisecom iTN2100 Hardware Description Download Page 31 | Manualshive

Page: 31 / 312

Raisecom iTN2100 Hardware Description Download Page 31

Raisecom
iTN2100 (P100R002) Hardware Description

Overview

Raisecom Technology Co., Ltd.

2

Fan

The iTN2100 is equipped with an independent and intelligent 19-inch 1-U fan named
FANS360.

Power supplies

The iTN2100 uses socket power supplies. It supports dual-DC, dual-AC, or hybrid AC/DC
power supplies. It also supports -48 V or 110 V DC power input and 110 V or 220 V DC
power input.

Dust-proof mesh

The bottom of the iTN2100 can be installed with a dust-proof mesh to prevent dusts in air
from accessing the iTN2100 through the airflow of the fan. This helps avoid influencing the
device performances.

Cards

The iTN2100 provides a wide variety of interfaces, thus implementing integrated service
access.

Table 1-1 lists all cards on the iTN2100 and their corresponding BUS.

Table 1-1

All cards on the iTN2100 and their corresponding BUS

Card

Type

BUS

NMS card

iTN2100-NMS

ETH BUS

SDH aggregation card

OPCOM3500E-2STM1/4-M

SDH BUS

SDH tributary card

OPCOM3500E-STM1-S

OPCOM3500E-4STM1-S

Ethernet aggregation card

iTN2100-NTU-4GF

ETH BUS

Ethernet switching service
card

iTN2100-PTU-4GE

ETH BUS

Ethernet access card

iTN2100-16GF

iTN2100-8FX

iTN2100-2IGC

OPCOM3500E-4FX

OPCOM3500E-8FX

Clock card

iTN2100-TSU

SDH BUS

TDMoP card

iTN2100-CES-16E1T1-BL

ETH BUS

EoP card

OPCOM3500E-EOPFE

SDH BUS

OPCOM3500E-EOP3FE

«
...
29
30
31
32
33
...
»

Summary of Contents for iTN2100

























































































































































































































































































































Reviews:

No comments