manualshive.com logo in svg

Raisecom iTN2100, Hardware Description, Page: 204 / 312

Share
Download
Raisecom iTN2100 Hardware Description Download Page 204

Raisecom 
iTN2100 (P100R002) Hardware Description 

15 PDH and RCMS cards 

 

 

Raisecom Technology Co., Ltd. 

175 

 

LED 

Status 

Description 

LPR 

(1–4) 

Red 

LPR LED for remote device that is connected to related optical 
interfaces 

 

Red: the remote device is powered off, when the remote 
device, which is connected to the local device and optical 
interfaces (Line), is working properly. 

 

Off: the remote device that is connected to related optical 
interfaces (Line) is working properly. 

 

LOS 

(1–4) 

Red 

LOS alarm LED on related optical interfaces (Line)   

 

Red: input LOS alarm occurs on related optical interfaces 
(Line). 

 

Blinking red: optical related interfaces (Line) receive signals 
properly. However, input LOS alarm occurs on connected 
remote devices.   

 

Off: related optical interfaces (Line) and connected remote 
devices receive signals properly or optical module does not 
exist.

 

 

15.9.5 Alarms 

Table 15-50 lists alarms of the OPCOM3500E-240GEx4L. 

Table 15-50

 

Alarms of the OPCOM3500E-240GEx4L 

Alarm 

Cause 

Level 

Optical interface LOS 
alarm 

 

Received signals are attenuated dramatically. 

 

The peer sender fails. 

 

Fiber connector of the sender is dirty or is not 
connected properly. 

 

Local receiver fails. 

Critical 

Remote device LPR 
alarm 

The remote device is powered off. 

Critical 

 

15.9.6 Specifications 

Table 15-51 lists specifications of the OPCOM3500E-240GEx4L. 

Table 15-51

 

Specifications of the OPCOM3500E-240GEx4L 

Item 

Value 

Dimensions 

25 mm (width) × 232 mm (depth) × 240 mm (height) 

Weight 

< 0.4 kg 

Max. power consumption  19 W 

 

Summary of Contents for iTN2100

























































































































































































































































































































Reviews:

No comments