Raisecom iTN2100 Hardware Description Download Page 184

Page: 184 / 312

Raisecom
iTN2100 (P100R002) Hardware Description

15 PDH and RCMS cards

Raisecom Technology Co., Ltd.

155

15.5.3 Interfaces

Interface types

There are four interfaces on the OPCOM3500E-120EOS×4 panel, as listed in Table 15-22.

Table 15-22

Interfaces on the OPCOM3500E-120EOS×4

Interface

Type

Description

A, B, C, D

1×9 optical interface



Service downlink interface



TX indicates sending and RX indicates receiving.

15.5.4 LEDs

There are 11 LEDs on the OPCOM3500E-120EOS×4 panel, as listed in Table 15-23.

Table 15-23

LEDs on the OPCOM3500E-120EOS×4 panel

Interface

Status

Description

PWR

Green

Power LED



Green: the power supply is normal.



Off: the power supply is abnormal.

SYS

Green

System status LED



Green: the system is working improperly.



Off: the system is working improperly.



Blinking green: the system is working properly.

ALM

Red

Office overall alarm LED



Red: one or more of TU-AIS, TU-LOP, E1-LOS, optical
interface LOF, and 1E-3 alarms are generated on local
optical interfaces A, B, C, or D.



Off: no TU-AIS, TU-LOP, E1-LOS, optical interface LOF,
and 1E-3 alarms are generated.

LPR (A–D)

Red

Optical interface A/B/C/D remote device LPR alarm LED



Red: after the local device and the remote device connected
to interface A, B, C, or D are connected and work properly,
LPR occurs on the remote device.



Off: the remote device connected to interface A, B, C, or D
is working properly.

LOS (A–D)

Red

Optical interface A/B/C/D LOS alarm LED



Red: input LOS alarms are generated on interface A, B, C,
or D.



Off: no input LOS alarms are generated on interface A, B,
C, or D.



Blinking green: input LOS alarms are generated on the
remote device connected to interface A, B, C, or D.

Summary of Contents for iTN2100

























































































































































































































































































































Search results

Summary of Contents for iTN2100

Reviews:

Raisecom iTN2100, Hardware Description, Page: 184 / 312

Search results

Summary of Contents for iTN2100

Reviews: