manualshive.com logo in svg

Raisecom iTN2100, Hardware Description, Page: 170 / 312

Share
Download
Raisecom iTN2100 Hardware Description Download Page 170

Raisecom 
iTN2100 (P100R002) Hardware Description 

15 PDH and RCMS cards 

 

 

Raisecom Technology Co., Ltd. 

141 

 

15.2.3 Interfaces 

Interface types 

There are two interfaces on the OPCOM3500E-32E1/32E1-BL, and the interfaces on the two 
cards are the same, as listed in Table 15-7. 

Table 15-7

 

Interfaces on the OPCOM3500E-32E1/32E1-BL panel 

Interface 

Connector type 

Description 

E1 1–16, 

E1 17–32 

SCSI female connector 

(100pin) 

 

The OPCOM3500E-32E1 has two unbalanced 
interfaces. 

 

The OPCOM3500E-32E1-BL has two balanced 
interfaces. 

 

Each interface transmits 16 ways of E1 services. 

 

Interface parameters 

Table 15-8 lists parameters of the SCSI interface on the OPCOM3500E-32E1/32E1-BL. 

Table 15-8

 

Parameters of the SCSI interface on the OPCOM3500E-32E1/32E1-BL 

Parameter 

Description 

Connector type 

SCSI female connector (100pin) 

Nominal rate 

2048 Kbit/s±50 ppm 

Line code 

HDB3 

Interface impedance 

 

75 

Ω

 for the unbalanced interface 

 

120 Ω for the balanced interface 

Electrical parameters 

Comply with ITU-T G.703 recommendations. 

Frame structure 

Comply with ITU-T G.704 recommendations. 

Jitter 

Comply with ITU-T G.823 recommendations. 

 

15.2.4 LEDs 

There are three LEDs on the OPCOM3500E-32E1/32E1-BL panel, and the LEDs are the 
same on the two cards, as listed in Table 15-9. 

Table 15-9

 

LEDs on the OPCOM3500E-32E1/32E1-BL panel 

Interface 

Status 

Description 

PWR 

Green 

Power LED 

 

Green: the power supply is normal. 

 

Off: the power supply is abnormal. 

Summary of Contents for iTN2100

























































































































































































































































































































Reviews:

No comments