Raisecom iTN2100 Hardware Description Download Page 142

Page: 142 / 312

Raisecom
iTN2100 (P100R002) Hardware Description

13 EOP cards

Raisecom Technology Co., Ltd.

113

Interface

Status

Description

ACT

Green

Primary/Slave LED for the aggregation card

In dual-card protection mode:



Green: the card is primary.



Off: the card is slave.

In non-protection mode: it is Green.

LOF (1–4)

Red

LOF alarm LED



Red: input LOF alarms are generated on optical
interfaces 1, 2, 3, and 4.



Off: no input LOF alarms are generated on optical
interfaces 1, 2, 3, and 4.

LOS (1–4)

Red

LOS alarm LED



Red: input LOS alarms are generated on optical
interfaces 1, 2, 3, and 4.



Off: no input LOS alarms are generated on optical
interfaces 1, 2, 3, and 4.

13.9.5 DIP switches

Table 13-45 lists configurations of the DIP switch on the iTN2100-EOT-GESTM4.

Table 13-45

Configurations of the DIP switch on the iTN2100-EOT-GESTM4

SW1

Function

Status

Description

No.

Bit1

Set the optical
interface rate.

Set the rate of the first optical interface to STM-4;
others become invalid.

OFF

Set the rate of the four optical interface to STM-1.

Bit2

Set the valid
SDH interface.

The SDN interface on the backplane takes effect.
Meanwhile, the SDH interface on the front panel is
invalid.

OFF

The SDN interface on the front panel takes effect.
Meanwhile, the SDH interface on the backplane is
invalid.

By default, Bit1 is OFF.
When configuring the SDH interface on the backplane to take effect through Bit2, you
need to set Bit1 to ON.

Summary of Contents for iTN2100

























































































































































































































































































































Search results

Summary of Contents for iTN2100

Reviews:

Raisecom iTN2100, Hardware Description, Page: 142 / 312

Search results

Summary of Contents for iTN2100

Reviews: