manualshive.com logo in svg

Raisecom iTN2100, Hardware Description, Page: 127 / 312

Share
Download
Raisecom iTN2100 Hardware Description Download Page 127

Raisecom 
iTN2100 (P100R002) Hardware Description 

13 EOP cards 

 

 

Raisecom Technology Co., Ltd. 

98 

 

13.5.3 Interfaces 

Interface types 

There are eight interfaces on the OPCOM3500E-EOP-FEE1×8 panel, as listed in Table 13-21. 

Table 13-21

 

Interface on the OPCOM3500E-EOP-FEE1×8 

Interface 

Type 

Description 

– 

RJ45 electrical interface 

100BASE-TX interface 

 

Interface parameters 

Table 13-22 lists parameters of eight RJ45 interfaces on the OPCOM3500E-EOP-FEE1×8. 

Table 13-22

 

Parameters of eight RJ45 interfaces on the OPCOM3500E-EOP-FEE1×8 

Parameter 

Description 

Connector type 

RJ45 

Interface rate 

100Base-TX, support auto-negotiation (in this situation, it 
supports 100 Mbit/s full duplex only) 

Line code 

4B/5B block coding, MLT-3 Line code 

Duplex mode 

Full duplex 

Flow control 

IEEE 802.3x-based flow control in full duplex mode 

Line order 

Auto MDI/MDIX 

Compliance standard 

IEEE 802.3u 

 

13.5.4 LEDs 

There are 10 LEDs on the OPCOM3500E-EOP-FEE1×8 panel, as listed in Table 13-23. 

Table 13-23

 

LEDs on the OPCOM3500E-EOP-FEE1×8 panel 

Interface 

Status 

Description 

PWR 

Green 

Power LED 

 

Green: the power supply is normal. 

 

Off: the power supply is abnormal. 

SYS 

Green 

System status LED 

 

Green: the system is working improperly. 

 

Off: the system is working improperly. 

 

Blinking green: the system is working properly. 

Summary of Contents for iTN2100

























































































































































































































































































































Reviews:

No comments