Raisecom ISCOM6820-GP Hardware Description Download Page 53

Page: 53 / 61

Raisecom
ISCOM6820-GP (A) Hardware Description

5 Lookup table of LEDs

Raisecom Proprietary and Confidential

Lookup table of LEDs

Table 5-1 lists LEDs of the ISCOM6820-GP.

Table 5-1

LEDs of the ISCOM6820-GP

LED

Status

Description

PWR

Green

Power LED



Green: the power supply is working properly.



Off: the power supply is working improperly.

SYS

Green

System working LED



Fast blinking green (4 Hz): the system is initializing.



Slow blinking green (0.5 Hz): the system is working
properly.



Off: the system is working improperly.

LINK/ACT

(SFP optical
interface)

Green

Line working LED



Green: the interface is connected properly.



Blinking green: the interface is transmitting data.



Off: the interface is disconnected or connected
improperly.

LINK/ACT

(RJ45 electrical
interface
integrated LED)

Green

Line working LED



Green: the interface is connected properly.



Blinking green: the interface is transmitting data.



Off: the interface is disconnected or connected
improperly.

Summary of Contents for ISCOM6820-GP






























































Search results

Summary of Contents for ISCOM6820-GP

Reviews:

Related manuals for ISCOM6820-GP

Brands by name

Popular brands

Raisecom ISCOM6820-GP, Hardware Description

Search results

Summary of Contents for ISCOM6820-GP

Reviews:

Related manuals for ISCOM6820-GP

Brands by name

Popular brands