Raisecom ISCOM6820-GP Hardware Description Download Page 33

Page: 33 / 61

Raisecom
ISCOM6820-GP (A) Hardware Description

2 Components

Raisecom Proprietary and Confidential

Figure 2-14

Panel of the FANS380 module

2.8.3 LEDs

There are 2 LEDs on the FANS380 module.

Table 2-23 lists LEDs on the FANS380 module.

Table 2-23

LEDs on the FANS380 module

LED

Status

Description

PWR

Green

Power LED



Green: the power supply is working properly.



Off: the power supply is working improperly.

ALM

Red

Alarm LED



Red: the module is working improperly and an alarm is generated.



Off: the module is working properly.

2.8.4 Technical specifications

Table 2-24 lists technical specifications of the FANS380 module.

Table 2-24

Technical specifications of the FANS380 module

Parameter

Description

Dimensions

37 mm (Width) ×221.5 mm (Depth) ×85.5 mm (Height)

Weight

0.7 kg

Power consumption

22 W

Summary of Contents for ISCOM6820-GP






























































Search results

Summary of Contents for ISCOM6820-GP

Reviews:

Related manuals for ISCOM6820-GP

Brands by name

Popular brands

Raisecom ISCOM6820-GP, Hardware Description

Search results

Summary of Contents for ISCOM6820-GP

Reviews:

Related manuals for ISCOM6820-GP

Brands by name

Popular brands