Raisecom ISCOM6800 Hardware Description Download

Page: 28 / 84

Raisecom
ISCOM6800 (A)Hardware Description

3 Cards

Raisecom Proprietary and Confidential

Table 3-8

Parameters of the ESC interface

Parameter

Description

Connector type

RJ45

Working mode

Duplex UART

Electrical feature

RS-485/RS-232

Baud rate

9600 Baud

Cable specification

4-core shielded cable

3.2.4 LEDs

There are 5 LEDs on the SMCA card.

Table 3-9 lists LEDs on the SMCA card.

Table 3-9

LEDs on the SMCA card

LED

Quantity Status

Description

SYS/ALM

Green

System working status LED



Fast blinking green (4 Hz): the system is being
initialized.



Slow blinking green (1 Hz): the system is working
properly.



Off/Green: the system is working improperly.

Red

Alarm LED



Red: a fault is generated.



Blinking red: the card is inserted improperly.



Off: no fault is generated.

Orange

Standby LED



Orange: the card is in standby status.



Off: the card is not in standby status.

When the card is in standby status, other
LEDs are off.

ACT

Green

Primary and secondary signal LED



Green: the card is a primary one.



Off: the card is a secondary one.

100M

Green

Interface rate LED



Green: the electrical interface is working at 100
Mbit/s.



Off: the electrical interface is working at 10
Mbit/s.

Summary of Contents for ISCOM6800





















































































Search results

Summary of Contents for ISCOM6800

Reviews:

Related manuals for ISCOM6800

Brands by name

Popular brands

Raisecom ISCOM6800, Hardware Description

Search results

Summary of Contents for ISCOM6800

Reviews:

Related manuals for ISCOM6800

Brands by name

Popular brands