Raisecom Gazelle S1020i-LI User Manual Download Page 52 | Manualshive

Page: 52 / 71

background image

Raisecom
Gazelle S1020i-LI (A) User Manual

4 Hardware installation

Raisecom Proprietary and Confidential

Copyright © Raisecom Technology Co., Ltd.

41

4.4.3 Connecting power cable

Connecting DC power cable



Confirm the power type supported by the Gazelle S1020i-LI before installing the
power cable. Connect the proper power voltage to the corresponding PINs
according to the marks displayed on the device shell. Otherwise, the Gazelle
S1020i-LI will be damaged or fail to be started normally.



Ensure that the ground cable is correctly grounded before connecting the power
cable.



Disconnect all power supplies before connecting or removing the power cable.



Use the power cable which meets the technical specifications.

The DC power interface of the Gazelle S1020i-LI is a 2-PIN Phoenix terminal. Connect the
DC power cable as below:

Step 1

Make the DC power cable according to specifications.

Step 2

Insert the DC power connector into the DC power interface of the Gazelle S1020i-LI snuggly
and tighten the screws at both sides of the connector, as shown in Figure 4-8.

Figure 4-8

Connecting the DC power connector

Step 3

Connect the other end of the DC power cable to the cabinet or the power sourcing equipment
in the machine room.

4.5 Powering on device

Power on the Gazelle S1020i-LI as below:



The Gazelle S1020i-LI can be powered on after being inserted with the power cable and
installed properly.



The Gazelle S1020i-LI is powered on when the power LED (PWR) is lightening up.



The Gazelle S1020i-LI begins to operate properly after Power-on Self-Test (POST) and
initialization. Interface LEDs indicate the working status of the interface (lit up, off, or
blinking)

«
...
50
51
52
53
54
...
»

Summary of Contents for Gazelle S1020i-LI








































































Reviews:

No comments

Related manuals for Gazelle S1020i-LI

Brand: Alyseum Pages: 7

TNS5800-8GP16GT-P24VDC

Brand: 3onedata Pages: 3

Brand: Vega Pages: 28

Brand: Sangamo Pages: 2

Brand: König Pages: 8

Brand: Watt Stopper Pages: 10

Brand: Wavetronix Pages: 3

Brand: Icy Box Pages: 10

Brand: hager Pages: 3

Brand: Lindy Pages: 5

IES2100SL Series

Brand: 3onedata Pages: 3

Brand: Ubiquiti Pages: 23

Brand: Exsys Pages: 2

IDS-105FE Series

Brand: Perle Pages: 2

Brand: Xantech Pages: 5

Brand: I-Tech Pages: 22

Brand: H3C Pages: 38

PROFINET 4-port

Brand: Helmholz Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands