Raisecom Gazelle S1020i-GL Series User Manual Download Page 55

Page: 55 / 83

Raisecom
Gazelle S1020i-GL (A) User Manual

3 Technical specifications

Raisecom Proprietary and Confidential

Parameter

Description

Protection class

IP40

Environmental authentication

Comply with EU RoHS standard.

3.3 Technical specifications

3.3.1 Laser safety class

The laser beam in the fiber may hurt your eyes. Do not stare into the optical interface
during maintenance and installation.

According to the value of the laser Tx power, the Gazelle S1020i-GL laser belongs to Class 1
in terms of safety. In Class 1, the maximum Tx power on the optical interface is smaller than
10 dBm (10 mW).

3.3.2 Reliability indicators

The reliability indexes include system usability, average annual return rate, Mean Time to
Repair (MTTR), and so on, as listed in Table 3-3.

Table 3-3

Reliability indicators

Parameter

Requirements

System availability

99.999%. The annual failure time for the Gazelle
S1020i-GL should be no longer than 5 minutes.

Annually system mean repair rate

< 1.5%

MTTR

< 2 hours

3.4 EMC standards

The Gazelle S1020i-GL is compliant with the following Electromagnetic Compatibility
(EMC) standards:



Electro Magnetic Interference (EMI) meets CISPR 32 CLASS A requirements.



Static electricity meets IEC 61000-4-2 level 4 requirements.



Radiated Immunity Test (RIT) meets IEC 61000-4-3 level 3 requirements.



Electrical Fast Transient (EFT) meets IEC 61000-4-4 level 4 requirements (the Gazelle
S1020i-12GF-16GE-GS meets level 3 requirements).



Damped oscillatory wave meets IEC 61000-4-18 level 3 requirements.

Summary of Contents for Gazelle S1020i-GL Series




















































































Search results

Summary of Contents for Gazelle S1020i-GL Series

Reviews:

Related manuals for Gazelle S1020i-GL Series

Brands by name

Popular brands

Raisecom Gazelle S1020i-GL Series, User Manual

Search results

Summary of Contents for Gazelle S1020i-GL Series

Reviews:

Related manuals for Gazelle S1020i-GL Series

Brands by name

Popular brands