PARTS
BH010-1 BH010-020 Head
BH010-2 BH010 Sump (10”)
BH020-2 BH020 Sump (20”)
BH010-3 BH010/020 O-Rings
BH010-5 Wrench
SEDIMENT CARTRIDGES AVAILABLE
BC101 10” 1 micron Sed. Cartridge for BH010
BC1
10” 5 micron Sed. Cartridge for BH010
BC3
10” 25 micron Sed. Cartridge for BH010
BP5
10" 5 micron Sed. Cartridge for BH010
BP25
10" 25 micron Sed. Cartridge for BH010
BC201 20” 1 micron Sed. Cartridge for BH020
BC205 20” 5 micron Sed. Cartridge for BH020
BC225 20” 25 micron Sed. Cartridge for BH020
CARBON CARTRIDGES AVAILABLE (Chlorine, Taste & Odour)
BC2
10” 5 micron Carbon Cartridge for BH010 rated flow 3 US gpm (not for whole-house use)
BC202 20” 5 micron Carbon Cartridge for BH020 rated flow 6 US gpm (not for whole-house use)
Note: A sediment filter must be installed before the carbon cartridges to prevent premature plugging up of the cartridges due to dirt,
sediment etc.
Optional Parts
BH010/020 Mounting Bracket and Bolts - BH010-6
c)
Remove the sump from the filter heads and put aside until later. Using an appropriate sized adjustable wrench, screw in the adapters to the inlet
and outlet ports of the housing, taking care not to cross-thread.
DO NOT OVERTIGHTEN
fittings into plastic filter head or it may crack, about one to
two thread(s) should remain visible.
d)
Turn off water supply now and open a nearby faucet to drain water out of pipes and relieve pressure. Once all the water from the pipes is
drained,measure and cut pipe as required and plumb in other fittings as shown in either fig A.
CAUTION:
To protect the housing from damage due
to heat from soldering, wrap the ports in a wet cloth during soldering.
f)
Remove plastic wrap from filter cartridge (not included) and place it in sump, making sure it is centered. Screw on the sump onto the head
by turning counterclockwise to tighten. Hand tighten only.
DO NOT USE WRENCH AND OVERTIGHTEN.
g)
Open valves before and after the filter unit, slowly turn on water supply and check for leaks. Flush water for 10 minutes prior to use.
YOUR UNIT IS NOW IN OPERATION
CHANGING YOUR CARTRIDGE
You should change your cartridge when the water flow is noticeably reduced or every 4-6 months, whichever is earlier.
To replace cartridge, shut off
the inlet valve and open a faucet close by until pressure in the unit is relieved.
Using the supplied wrench, unscrew the sump. Discrad old cartridge and rinse sump. Insert new cartridge into the sump and screw sump back on to
filter. Handtighten only. DO NOT USE WRENCH TO TIGHTEN SUMP. Slowly open the water and flush for a few minutes before use.
MAINTENANCE
Lubricate both o-rings on the top of the sump periodically to prolong their life. Use food grade silicone lubricant or other non-petroleum based lubri-
cants only. Wash the filter sump with mild soap and water.
DO NOT
use harsh cleaners or hot water. If your unit is not used in winter, or will be subject
to freezing temperatures, drain unit and remove cartridges.
BH010-1
BH010-3
BH010-2
BH020-2
(not shown)
PARTS LIST AND CARTRIDGE OPTIONS
BH010-5
Thank you
for purchasing one of our ENVIROGARD / Rainfresh Water Filters. We are committed to ensuring that you are
totally
satisfied
. If you have any problems, don't go back to the store -
please contact us !
Most issues can be resolved over the phone. (Monday to Friday - 8:00 a.m. to 5:00 p.m. EST)
Help Line: 1-800-667-8072 Toronto & Area: 905-884-9388 Website:
www.rainfresh.ca
LIMITED WARRANTY
Envirogard system housings are warranted, to the original Consumer purchaser/owner, for a period of one (1) year, from the date of purchase, against defects in materials or workmanship.
Envirogard’s obligation under this warranty shall consist of repair, replacement or credit, at its option, of any part found by Company inspection to be defective, provided that the product
has not been misused, abused, altered or damaged as determined by the Company and provided that only approved Envirogard/Rainfresh replacement cartridges and seals have been used
in the housing. This warranty does NOT apply to the replacement cartridge which by nature will diminish in performance through normal use and requires regular replacement. This war-
ranty does NOT cover, and is intended to exclude, any liability on the part of Envirogard for any incidental damages, consequential damages, labour charges or any other costs incurred in
connection with the purchase, installation, use, maintenance or repair of the water filter whether under this warranty or any other warranty implied by law. Some provinces/states do not
allow the exclusion of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights and you may also have
other rights which vary from province to province/state to state. This warranty applies only to equipment purchased and installed in domestic residential
applications in Canada or the U.S.A. This warranty does NOT apply to commercial/industrial installations.
ENVIROGARD PRODUCTS LIMITED
446 Major Mackenzie Dr. E., Unit #6, Richmond Hill ON L4C 1J2 Canada
P.O. Box 64, Richmond Hill ON L4C 4X9 Canada
© COPYRIGHT * ENVIROGARD PRODUCTS LIMITED 2012 * ALL RIGHTS RESERVED
BH010/BH020 E Sept/12
pg 2.
Component
Drinking Water
Point of entry component tested and certified
by CSA International to CSA Standard B483.1.
and NSF/ANSI standard 61 for materials
and structural integrity requirements only.
Head
Sump
