Rainfresh 30T Installation And Operation Manual Download Page 3

 

 

INSTALLATION 

 
 
 
 
 
 

 
 
 
 
 
 
 
 
 
 

 

Figure 1. Piping Diagram

 

 

Electrical Requirements: 

 

The automatic control valve requires a constant power supply - 110V AC. We recommend a GFCI (ground fault circuit 
interrupter) outlet within 5 feet of the softener. Extension cords are not recommended.  

 

If water pipes are used to ground electrical system, you will need to install a jumper wire across the filter unit. 
 

Unpacking the unit 

The unit includes: 

1)

 

The main unit with electronic metered automatic control valve and bypass valve 

2)

 

Salt tank with brine float and 3/8” tubing to connect to main unit 

3)

 

Inlet outlet elbow fittings (2 ) 

4)

 

Allen key to open and close bypass valve 

5)

 

Drain hose – 15 ft 

6)

 

AC power adapter 

7)

 

Instruction manual 

Unpack the unit and place it at the location where you intend to install the unit. 

 

Stand back and look at the softener to make sure it is standing straight up and not tilted to one side. Make sure your 
chosen location will be fairly level, dry, and protected from possible freezing conditions. The softener can sit directly on 
the floor and will not corrode. DO NOT set the softener or salt tank onto make shift platforms 
as this can cause damage or may cause it to topple. 

 

 

The system has 3 connections - an inlet, an outlet, and a drain line connection. If you are 
looking at the back of the unit (fig 2A), the inlet is on the left side. 

Warning: 

Make sure that 

you have correctly identified the inlet of the system. REVERSING THE CONNECTIONS WILL 
RESULT IN RESIN BEADS BEING THROWN INTO YOUR HOME'S PLUMBING SYSTEM CAUSING 
DAMAGE TO IT AS WELL AS THE SOFTENER.  

 

The following pipe can be used for installing your new system - Copper, CPVC, and PEX are the most popular.  

 

Plumbing in your softener  

 

If your hot water tank is electric, turn off the power to it to avoid damage to the element in the tank.  

 

Well Pump 

Pressure 

Tank 

Rainfresh Softener 

Water Heater 

City Water Supply 

Well Water 
Supply 

OR 

Cold water to house 

Hot water to house 

Optional bypass to 
outside faucets 

Rainfresh 

Sediment Filter 

(Recommended) 

Water Meter 

To air-gap 

drain 

WATER 

IN 

WATER 

OUT 

Fig 2A 

Optional 

Rainfresh UV 

Disinfection System & 

filter for well water

 

Summary of Contents for 30T











Reviews: