Rainbow 271023 Installation Instructions Manual Download Page 12

Important 

operational 

notice       DPA 

1.2500 

 
The amplifier is provided for the use on a 12 V step-down system or for presentation purpose on a 12 
– 14,3 V / 25 A power supply. The connection on another supply point is not allowed.  
In case of a defect fuse, please replace only with the same type. Please pay attention for the 
indications on the defect fuse. In case the new fuse should be defect again, than there might be an 
error in the system. The opening of the amplifier for the change of components, piece parts or the 
function, as well as the self repair is not allowed. In case of non-observance, the guarantee claims 
will expire. 
 
Due to safety technical reasons, you should only fix the amplifier with the included sheet metal 
screws. In case of other fixing methods, we will not be held liable for. 
 

Safety instructions for the user in order to prevent injuries and accidents: 

The products are only suitable for users with the necessary installation knowledge. The relevant 
safety regulations for bearing car body parts, instructions on the vehicle safety inside, as well as the 
regulations of the competent vehicle manufacturer are necessary to be observed. 
 

Guarantee 

regulations        DPA 

1.2500 

 
With this user guarantee the Rainbow GmbH in Bad Rappanau guarantees on the product from the 
date of the first purchase or the first installation by the authorised specialist dealer a 12 months 
guarantee on material and manufacturing. 
 
The guarantee is limited to the replacement of defective components, which have defect due to 
construction- or material fault, as well as to the guarantee repair. 
 
Accidents, acts of god or other causes, which Rainbow is not responsible for, in particular water and 
fire are not included in the guarantee. 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

901133 

Edition: MPJ/1.0 – 11/00 

 

This installation instruction is copyrighted. Each duplication or reprinting, also part of it and each 

reproduction of the pictures, also in a different version, is only permitted with a written allowance of the 

Rainbow company. 

Copyright © 2000 Rainbow GmbH. Rainbow is a registered Trademark. 

 

 

 

 

 

 

 

12 

Summary of Contents for 271023













Reviews: