background image

CHANGING THE CCU’S 

PROM CHIP

Important

• Before working with the circuit board, turn off

all power to the Control Unit Board.

• Before working with the circuit board, make

sure you are grounded and are working in a

static-free environment. Static charges can

damage the chips.

• Do not perform any operations on the circuit

board unless advised to do so by an

Authorized Rain Bird Service technician.

• The PROM chip is located in the upper center of the

Control Unit Board. It typically is labeled with a large

white sticker.

• The PROM chip rests inside a plastic cradle. Using the

tabs at either end of PROM chip, gently wiggle the chip

and lift it straight up until it comes free.

• After removing the chip, notice that one end of chip

has one vertical tab, while the other end has two verti-

cal tabs. These tabs fit into corresponding grooves in

the cradle.

• To replace the PROM chip with a new chip, align the

vertical tabs with the grooves in the cradle. The chip

will not fit in the cradle if the chip is turned the wrong

direction.

• Gently press the chip into place.

ESP-LX Plus Site Satellite Controller Addendum

18

Summary of Contents for AESPLX16SM





















Reviews: