Rail King Y6b 2-8-8-2 Operating Instructions Manual Download Page 2

Page: 2 / 24

RailKing Y6b 2-8-8-2 Steam Engine

Table of Contents

Set Up

Basic Operation

Throttle

Operation Buttons

Volume Control

Proto-Sound 2.0 Operation

Activating Proto-Sound 2.0 Conventional Mode Features

Freight Yard Sounds (FYS)

Tips on Using FYS

Proto-Coupler

Operation

Speed Control

Lock into a Direction State

Reset to Factory Defaults

Automatic Sounds

Maintenance

Lubrication and Greasing Instructions

Cleaning the Wheels, Tires and Track

Locomotive Traction Tire Replacement

Smoke Unit Maintenance

Locomotive Light Bulb Replacement

Self-Charging Battery Back-Up

Troubleshooting

Compatibility

Transformer Compatibility Chart

Additional Features with DCS Remote Control System

Safety Precautions

Service and Warranty Information

Summary of Contents for Y6b 2-8-8-2

























Search results

Summary of Contents for Y6b 2-8-8-2

Reviews:

Related manuals for Y6b 2-8-8-2

Brands by name

Popular brands

Rail King Y6b 2-8-8-2, Operating Instructions Manual

Search results

Summary of Contents for Y6b 2-8-8-2

Reviews:

Related manuals for Y6b 2-8-8-2

Brands by name

Popular brands