background image

PS 3.0 Enhancements

®

There are 4 options for operating your MTH Proto-Sound  3.0-equipped engine; 

-Conventional AC

-Conventional DC

-DCS [MTH Digital Command System]

-DCC

When the locomotive is placed on the track and power is applied to the track the 

locomotive will detect the type of control system being used and respond accordingly.

Below is an overview of the 4 different systems.

NOTE: You’ll need to have the DCC/DCS switch set correctly if your using one of 

those two modes.

® 

Here are some of the exciting changes incorporated into your new MTH Proto-Sound

3.0 Locomotives. More advanced features such as Custom Speed Tables and Advanced 

Consisting can be found in the DCC section of this manual.

Conventional (Analog) AC/DC Start-up/Shut-down

Your new MTH PS3.0-equipped locomotive no longer has batteries. It uses Super 
Capacitors to hold the engine board alive for a short time when you shut off or 
interrupt track power. Because of this, when you first apply track power to your PS3.0-

equipped O Gauge engine, you will notice the headlight comes on but nothing else. 
This is perfectly normal. The capacitors are charging up during this time. The wait 
time depends upon how long it’s been since you last applied power to the engine. 

Typically it will take 1-15 seconds to fully charge. 

NOTE: The 1-15 second charging 

wait time ONLY applies to conventional AC track power.

Once the headlight shuts off, the engine will play its start-up sounds and all the lights will 

come back on, simultaneously. Smoke too if you have it turned on.

The capacitors hold enough charge to play the full shut-down sounds. Also, the 
capacitors allow you to operate your engine in conventional mode just like you would 
any other conventionally-controlled engine. Finally, because there are no batteries, you 
will notice there is no external charge jack on the engine.

 

Activating DCC Mode

Your MTH Locomotive has a DCC Decoder installed. However, in order to activate
DCC Mode, you must install a DCS/DCC switch.

For Installation instructions, please contact MTH Electric Trains
Telephone: 410-381-2580; Fax: 410-423-0009;
[email protected],
7020 Columbia Gateway Drive, Columbia MD 21046-1532

RailKing 

 Diesel Engine w/Proto-Sound® 3.0

5

SD60

Summary of Contents for SD60


















































Reviews: