Rail King 0-8-0 Steam Engine Operating Instructions Manual Download | Manualshive

Page: 29 / 36

background image

29

RailKing 0-8-0 Operating Manual

over the wheel. If a twist occurs, the tire will have to be removed and
reinstalled or a noticeable wobble in your engine will occur when operating
the locomotive. In addition, it is important to make sure that the tire is
fully seated inside the groove. Any portion of the tire extending out of the
groove can cause the engine to wobble. A razor blade can be used to trim
away any excess tire that doesn’t’t seat itself inside the groove properly.

Replacement tires are available directly from MTH Electric Trains.

HEADLIGHT REPLACEMENT

The locomotive’s headlights are controlled by the track voltage and will

glow with greater intensity depending on the transformer voltage setting.
The headlight can be easily removed from its lampholder should the bulb
expire. To remove the bulb, follow the boiler removal instructions found in
the Lubrication section on the proceeding pages. Once the boiler has been
removed, remove the two smoke unit assembly screws located under the
headlight assembly so that you can slide the smoke unit assembly back and
access the headlight wire harness. To remove the headlight bulb and
harness, gently remove the headlight gromet with a pair of needle nose
pliers. Do not pull directly on the wire harness itself. Once the gromet is
removed the bulb and harness should fall free and can be replaced.
Replacement bulbs are available directly from MTH Electric Trains.

«
...
27
28
29
30
31
...
»

Summary of Contents for 0-8-0 Steam Engine





































Reviews:

No comments

Related manuals for 0-8-0 Steam Engine

Brand: E-FLITE Pages: 17

Habu 32 EDF ARF

Brand: E-FLITE Pages: 56

Brand: Vollmer Pages: 4

Brand: AMATI Pages: 56

Brand: Faller Pages: 16

Brand: Uberstix Pages: 40

Brand: marklin Pages: 32

Brand: Gold Wing Pages: 45

SCOOBY-DOO 75901

Brand: LEGO Pages: 67

Brand: GREAT PLANES Pages: 20

MAN F2000 Evolution

Brand: ROBBE Pages: 44

Disc-Oh Flyers BX1592

Brand: B.toys Pages: 2

Toot-Toot Drivers 3-in-1 Raceway

Brand: VTech Pages: 16

Rocket Boost Roller Coaster

Brand: KNEX Pages: 64

NSWGR C34 4-6-0

Brand: Australian Railway Kits Pages: 12

Zoom Lynx Mk.8 seatbelts STEEL

Brand: Eduard Pages: 4

LICHTENSTEIN CASTLE

Brand: Faller Pages: 8

G.I. Joe Sting Raider

Brand: Hasbro Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands