Raider RDP-CDL21, User Manual

Page: 14 / 112

14
www.raider.bg
1.5.12. Do not place any metal objects in the charger.
1.5.13. Do not change the direction of rotation of the spindle of the cordless drill during operation.
This will damage her.
1.5.14. To clean the cordless drill, use soft and dry cloth. Never use any solvent or alcohol.
1.5.15. Before cleaning the charger, unplug the charger.
1.5.16. If you are going to charge batteries consecutively one after the other, make a 30-minute
break between charges.
1.6. Special safety precautions when operating the charger.
Before charging the charger, all relevant information and information contained in this instruction
manual as well as the charger and battery charging instructions for this charger must be read.
1.6.1. To reduce the risk of personal injury and injuries, the charger must only be used to charge
nickel-cadmium batteries. Other types of batteries may explode, cause serious injuries or other
material damage.
1.6.2. Do not expose the charger to the influence of moisture or water.
1.6.3. The use of connection, non-recommended or non-sold items by the charger manufacturer
is liable to cause a fire, cause bodily injury or electric shock.
1.6.4. The power cord should not be inserted. It should not be in a passage where people pass
and should not be subjected to any other danger (for example too much tension).
1.6.5. If there is no need, do not use an extension. Using an inappropriate extension may cause
a fire or electric shock. If using an extension cord is necessary, first make sure that the extension
of the extension extends to the pins of the original power supply plug.
1.6.6. The extension must be in the correct technical condition.
1.6.7. Do not use the charger with a damaged power cord or plug. The fault must be removed
by a qualified person.
1.6.8. It is not allowed to use the charger if it has been subject to a strong shock, fall or has been
damaged in any other way. Verification and eventual repair must be entrusted to an authorized
RAIDER service center.
1.6.9. Do not disassemble the charger. All repairs should be entrusted to an authorized RAIDER
service center. Incorrect installation of the charger will cause an electric shock or fire.
1.6.10. Before proceeding with any service or cleaning the charger, it must be disconnected from
the mains.
1.6.11. Disconnect the charger from the mains when not in use!
2. Design and use.
The cordless drill is a power tool powered by a battery. It is driven by a DC electric motor with
permanent magnets and a planetary gear with cylindrical gears. The cordless drill is designed
to screw and unscrew screws and bolts in wood, metal and plastics as well as drill holes in the
listed materials. Power tools with cordless, cordless power supply are especially suitable for
work related to interior decoration, room adaptation, and more.
It is not allowed to use the power tool for activities other than its intended purpose!
3. Noise and vibration data.
Sound pressure level: LpA = 77.8 dB (A) K = 3 dB (A)
Sound power level: LwA = 88.8 dB (A) K = 3 dB (A)
Vibration acceleration value: ah = 0.670 m / s2 <2.5 m / s2 K = 1.5 m / s2.
4. Preparing for work.
4.1. Inserting and removing the battery.
Move the direction switch (2) to the intermediate position. In this situation, the starter switch (1)
is blocked.
Press the button (3) and the battery (12) is pulled forward.
Insert the charged battery (12) into place and until the lock button (3) is clear.
4.2. Charge the battery.
The cordless drill is supplied with a partially charged rechargeable battery.The battery must be
fully charged before use. Charging should be carried out at an ambient temperature in the range