16
www.raider.bg
• Unscrew the adjusting knob on the front and
tilt the motor, then remove the transport packing.
• Now place one by one the uprights in the
casing of the sawing bench.
• Secure the uprights with screws using a
screwdriver, do not completely tighten the screws
• Fit the 4 support bars, do not completely
tighten the screws
• Fit the black plastic bottom plate and screw
it tight.
• Attach the rubber feet under the uprights
• Turn the machine into an upright position on
a flat surface and adjust the machine so that it
stands in a stable position, tighten all the nuts and
bolts
Assemble bracket/push stick
• Attach the 2 brackets onto the casing of the
sawing bench and screw them tight .
• Place the push stick in the brackets.
Assembly and attachment of the rip fence •
Attach the aluminium fence to the positioning
block.
• Now you can attach the complete rip fence
to the bench top.
• Slide the rip fence via one end of the
positioning rail over the bench top.
• Adjust the position of the aluminium fence
profile such that the end corresponds to the rear
edge of the saw.
Assembly of the riving knife and the protective
cap
• Turn the saw blade completely upwards.
• Remove the bench inlay.
• Assemble the riving knife on the set-up for
this purpose and use hereby the Allen screws and
the filling rings. Ensure that the riving knife falls
properly into the opening (= groove).
• Now put the inlay back in the bench and
fasten it.
• Now assembly the protective cap onto the
riving knife and use hereby the profiled nut and
self-locking nut. Now lay a lath against the saw
blade and the riving knife and check whether it
falls properly into the extension of the saw blade.
If this is not the case: Loosen the fastening bolts
and place or remove the filling rings.
• Above the saw table the radial distance
between the riving knife and the toothed rim of
the saw blade shall not at any point exceed 5 mm
at the depth of cut set.
• The tip of the riving knife shall not be lower
than 5 mm from the tooth peak, as shown.
Assembly of the saw blade First remove the
plug from the mains before the saw blade is
assembled or replaced.
• Remove the inlay from the bench. Use a
screwdriver for this purpose.
• Turn the saw axle completely upwards.
Remove the nut and the outside flange from
the saw axle.
• Now slide the saw blade over the saw axle
and now put the outside flange and the nut back.
Tighten the nut by hand.
• Now use the 2 keys: one for the flange and
one for the nut and now clamp it.
• Now put the inlay back in the bench and
fasten it.
Mounting the push stick holders
Mount both push stick holders on the side of
the machine using the bolts and rings supplied.
USE OF THE MITRING SET-UP
By turning the handle at the side of the
machine you can adjust the saw blade to a
maximum of 45° .
6. STARTING UP THE CIRCULAR SAW
TABLE
• The machine is switched off by pressing the
red button.
• The machine is switched on by pressing the
green button.
If the mains voltage is interrupted or the mains
plug is taken out of the wall socket, the machine
will immediately be switched off by the safety
switch. If the mains voltage then suddenly comes
back on, the sawing machine will not be switched
on. It will only be switched on again when the
green button is pressed.
7. DUST EXTRACTOR
The dust capture system is suitable for
connecting with vaccum cleaner.
8. USING THE MACHINE
SAWING
Take care that your hands do not get too close
to the saw blade during sawing.
To saw, proceed as follows:
• Undo the two screws in the rip fence at the
side of the table.
• Set the rip fence to the size you require.
• Re-tighten the screws.
• Set the saw guard to the correct height.
• Switch the machine on.
• Press the work slowly and with the minimum
of pressure against the saw blade.
• When the end of the work approaches the
saw blade, use a push stick to feed the work