background image

  

9

With the SuperCat MX, there is no need to 

arm the motor.  Simply squeeze the trigger in, 

or towards the driver for the boat to move 

forward.

Binding is the process of programming the receiver to recognize the GUID (Global Unique Iden�fier) code

of a single specific transmi�er. When a receiver is bound to a transmi�er, the receiver will only respond to

that specific transmi�er. If you need to rebind for any reason, please follow these steps:

1. Make sure that the transmi�er is turned off.

2. Plug in the ba�ery in the boat to power up the receiver.

3. Turn on the transmi�er within 5 seconds of powering up the receiver.

4. The receiver and transmi�er will auto-bind within a few seconds and you will have control over all 

    func�ons and be ready to run.

5. If binding is successful, the blinking light will turn solid.  If not, start the binding process again with 

     step 1.

Pushing the trigger in the opposite direc�on, or 

away from the driver, will move the boat in the 

reverse direc�on.

With the propor�onal speed control, the further

you pull the trigger, the faster your boat will go.

To stop, release the trigger.

Rotate the steering wheel to the right, or clockwise

to turn the boat to the right. If you need more 

control, move the Dual Rate switch up for �ghter

turns.

Receiver Connection and Binding

How to Operate Your Boat

Summary of Contents for SUPERCAT MX

















Reviews: